Read Sharp CD-XP300 (serv.man6) Service Manual online
– 7 –
CD-XP300H
Troubleshooting chart
General
CD player
Tuner
Cassette deck
Remote control
Condensation
Symptom
Possible cause
The clock is not on time.
Did a power failure occur? Reset the
clock.
clock.
When a button is pressed, the unit
does not respond.
does not respond.
Set this unit to the power stand-by mode
and then turn it back on.
and then turn it back on.
If the unit still malfunctions, reset it.
No sound is heard.
Is the volume level set to "0"?
Are the headphones connected?
Are the speaker wires disconnected?
Symptom
Possible cause
Playback does not start.
Is the disc loaded upside down?
Playback stops in the middle or is
not performed properly.
not performed properly.
Does the disc satisfy the standards?
Is the disc distorted or scratched?
Playback sounds are skipped, or
stopped in the middle of a track.
stopped in the middle of a track.
Is the unit located near excessive vibra-
tions?
tions?
Is the disc very dirty?
Has condensation formed inside the unit?
Symptom
Possible cause
Radio makes unusual noise con-
secutively.
secutively.
Is the unit placed near the TV or compu-
ter?
ter?
Is the FM aerial or AM loop aerial placed
properly? Move the AC power lead or the
unit away from the aerial if located near.
properly? Move the AC power lead or the
unit away from the aerial if located near.
Symptom
Possible cause
Cannot record.
Is the erase-prevention tab removed?
Cannot record tracks with proper
sound quality.
sound quality.
Is it a normal tape? (Yo u cannot record on
a metal or CrO tape.)
a metal or CrO tape.)
Cannot erase completely.
Sound skipping.
Is there any slack?
Is the tape stretched?
Cannot hear treble.
Are the capstans, pinch rollers, or heads
dirty?
dirty?
Sound fluctuation.
Cannot remove the tape.
If a power failure occurs during playback,
the heads remain engaged with the tape.
Do not open the compartment forcibly.
Wait until electricity resumes.
the heads remain engaged with the tape.
Do not open the compartment forcibly.
Wait until electricity resumes.
Symptom
Possible cause
The remote control does not oper-
ate.
ate.
Is the AC power lead of the unit plugged
in?
in?
Is the battery polarity respected?
Are the batteries dead?
Is the distance or angle incorrect?
Does the remote control sensor receive
strong light?
strong light?
Sudden temperature changes, storage or opera-
tion in an extremely humid environment may
cause condensation inside the cabinet (CD pick-
up, tape heads, etc.) or on the transmitter on the
remote control.
Condensation can cause the unit to malfunction.
If this happens, leave the power on with no disc
(or cassette) in the unit until normal playback is
possible (about 1 hour). Wipe off any condensa-
tion on the transmitter with a soft cloth before op-
erating the unit.
tion in an extremely humid environment may
cause condensation inside the cabinet (CD pick-
up, tape heads, etc.) or on the transmitter on the
remote control.
Condensation can cause the unit to malfunction.
If this happens, leave the power on with no disc
(or cassette) in the unit until normal playback is
possible (about 1 hour). Wipe off any condensa-
tion on the transmitter with a soft cloth before op-
erating the unit.
If trouble occurs
If such a problem occurs, do the following:
1
1
Set the unit to the stand-by mode and turn the power on again.
2
Note:
If neither operation above restores the unit, clear all the memory by resetting it.
Clearing all the memory (reset)
1
Press the ON/STAND-BY button to enter the power stand-by mode.
2
Whilst pressing down the CLOCK button and the EQUALIZER/X-BASS/DEMO
button, press the ON/STAND-BY button until "CLEAR AL" appears.
button, press the ON/STAND-BY button until "CLEAR AL" appears.
Caution:
Before transporting the unit
On the back of this unit is equipped with a transport screw in order to prevent damage
during transportation.
during transportation.
1
Press the ON/STAND-BY button to turn the
power on.
power on.
2
Press the CD button.
3
Press the OPEN/CLOSE button to open
the disc tray.
Remove all CDs inserted in the unit.
the disc tray.
Remove all CDs inserted in the unit.
4
Press the OPEN/CLOSE button to close
the disc tray.
Make sure that "NO DISC" is displayed.
the disc tray.
Make sure that "NO DISC" is displayed.
5
Press the ON/STAND-BY button to enter the
stand-by mode, and then unplug the AC
power lead from the wall socket.
stand-by mode, and then unplug the AC
power lead from the wall socket.
6
Insert the transport screw into the back of
the unit and tighten it with a flat head screw-
driver or a coin.
the unit and tighten it with a flat head screw-
driver or a coin.
Troubleshooting chart
Remote control
Test of the remote control
Check the remote control after checking all connections have been made correctly.
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you can enjoy the
music.
music.
.
0.2 m - 6 m
(8" - 20')
(8" - 20')
Remote sensor
Display