Read Sharp CD-DVD500 User Guide / Operation Manual online
ENGLISH
72
CD-DVD500H
When timer indicator is flashing
When only TIMER indicator is flashing (other indicators have gone out), the unit is
overheated.
Due to a problem in the speaker circuit, the unit will enter the stand-by mode automati-
cally.
In this case, take the following corrective
actions.
overheated.
Due to a problem in the speaker circuit, the unit will enter the stand-by mode automati-
cally.
In this case, take the following corrective
actions.
1
. Unplug the AC power plug from the AC
socket.
2
. Make sure that the unit vent is not blocked.
3
. Make sure that the speaker wires have
been correctly connected to the speaker
terminals.
terminals.
4
. After checking items 2 and 3 above, wait
for 2 or 3 hours before trying to use the
unit.
unit.
5
. Reconnect the AC power lead.
The higher volume causes to flash the timer indicator. If it happens, lower the
volume.
volume.
■
Before transporting the unit
1.
Press the ON/STAND-BY button to turn the power on.
2.
Press the DVD/CD button.
3.
Press the
7
7
7
7
7
OPEN/CLOSE button to open
the disc tray.
Remove all discs from the unit.
Remove all discs from the unit.
4.
Press the
7
7
7
7
7
OPEN/CLOSE button to close
the disc tray.
Make sure that “NO DISC” is displayed.
Make sure that “NO DISC” is displayed.
5.
Press the ON/STAND-BY button to enter the
stand-by mode, “GOOD-BYE” is displayed.
stand-by mode, “GOOD-BYE” is displayed.
6.
When “GOOD-BYE” disappears, unplug
the AC power lead from the AC socket.
the AC power lead from the AC socket.
7.
Insert the transport screw into the back of
the unit and tighten it with a flat-blade
screwdriver.
the unit and tighten it with a flat-blade
screwdriver.
■
Clearing all the memory (reset)
1
. Press the ON/STAND-BY button to enter the power stand-by mode.
2
. Whilst pressing down the
0
0
0
0
0
button and X-BASS/DEMO button, press the
ON/STAND-BY button until “CLEAR AL” appears.
Caution:
This operation will erase all data stored in memory including clock, timer settings and
tuner preset.
tuner preset.
References
–
T
roubleshooting chart
–
■
Condensation
Sudden temperature changes, storage or operation in an extremely humid environ-
ment may cause condensation inside the cabinet (DVD/CD pickup, tape heads, etc.)
or on the transmitter on the remote control.
Condensation can cause the unit to malfunction.
If this happens, leave the power on with no disc (or cassette) in the unit until normal
playback is possible (about 1 hour). Wipe off any condensation on the transmitter with
a soft cloth before operating the unit.
ment may cause condensation inside the cabinet (DVD/CD pickup, tape heads, etc.)
or on the transmitter on the remote control.
Condensation can cause the unit to malfunction.
If this happens, leave the power on with no disc (or cassette) in the unit until normal
playback is possible (about 1 hour). Wipe off any condensation on the transmitter with
a soft cloth before operating the unit.
■
If trouble occurs
When this product is subjected to strong external interference (mechanical shock, ex-
cessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is oper-
ated incorrectly, it may malfunction.
cessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is oper-
ated incorrectly, it may malfunction.
If such a problem occurs, do the following:
1. Set the unit to the stand-by mode and turn the power on again.
2. If the unit is not restored in the previous operation, unplug and plug in the
2. If the unit is not restored in the previous operation, unplug and plug in the
unit, and then turn the power on.
Note:
If neither operation above restores the unit, clear all the memory by resetting it.
If neither operation above restores the unit, clear all the memory by resetting it.
Troubleshooting chart (continued)
Click on the first or last page to see other CD-DVD500 service manuals if exist.