Read Sharp CD-DP900 (serv.man7) User Guide / Operation Manual online
21
CD-DP900E(UK)_2.fm
02/1/8
CD-DP900E
T
a
pe Pl
a
y
bac
k
- L
ist
en
in
g
t
o
a c
ass
et
te
t
a
p
e
(
T
AP
E 1
o
r T
A
P
E
2)
-
Listening to a cassette tape (TAPE 1 or TAPE 2)
Before playback:
Playback is possible in TAPE 1 compartment as well as in TAPE 2.
To stop playback:
Press
the
(TAPE )
button.
Fast forward/rewind: (TAPE 2 only)
Caution:
To remove the cassette, press the (TAPE ) button, and then open the compartment.
Before changing from one tape operation to another, press the (TAPE ) button.
If a power failure occurs during tape operation, the tape head will remain engaged
with the tape and the cassette door will not open. In this case, wait until the power
is restored.
with the tape and the cassette door will not open. In this case, wait until the power
is restored.
For playback, use normal or low-noise tapes for the best sound.
(Metal or CrO tapes are not recommended.)
(Metal or CrO tapes are not recommended.)
Do not use C-120 tapes or poor-quality tapes, as they may cause mal-
functions.
functions.
Before loading a tape into the cassette compartment, tighten the slack
with a pen or a pencil.
with a pen or a pencil.
1
Press the ON/STAND-BY button to turn the power on.
2
Open the cassette door by pushing the area marked " PUSH EJECT".
3
Load a cassette into the TAPE 1 or TAPE 2
cassette compartment with the side to be
played facing toward you.
cassette compartment with the side to be
played facing toward you.
4
Press the TAPE (1 2) button to select the cassette you want to
listen to.
listen to.
5
Press the / button to start playback.
When playback is performed using the remote control, press the TAPE 1 or
TAPE 2 button.
TAPE 2 button.
1
Press the (TAPE ) button, then press the TAPE (1 2) button to select TAPE 2.
2
To advance the tape, press the
/
(
) button. To rewind it, press the
/
(
) button.
TAPE 1
TAPE 2
Sound control (See page 14.)
22
CD-DP900E(UK)_2.fm
02/1/8
CD-DP900E
T
a
p
e
Recor
d
in
g
- Rec
o
rd
in
g
t
o
a ca
sse
tt
e
ta
p
e
-
Recording to a cassette tape
Before recording:
When recording important selections, make a preliminary test to ensure that the
desired material is properly recorded.
desired material is properly recorded.
SHARP is not liable for damage or loss of your recording arising from malfunction
of this unit.
of this unit.
The volume and sound controls can be adjusted with no effect on the recorded
signal (Variable Sound Monitor).
signal (Variable Sound Monitor).
For recording, use only normal tapes. Do not use metal or CrO tapes.
Recording can be operated in the TAPE 2 compartment. The TAPE 1 is for playback only.
Recording from a CD (CDs)
You can record 3 CDs continuously.
To perform programmed recording:
To stop recording:
Press
the
(CD )
button.
The CD and tape will stop.
Notes:
When the end of the tape is reached whilst recording, the CD player will display
the track number which was being played at that time, and stop automatically. If
you want to restart recording from the beginning of the interrupted track, turn over
the tape, press the REC PAUSE (
the track number which was being played at that time, and stop automatically. If
you want to restart recording from the beginning of the interrupted track, turn over
the tape, press the REC PAUSE (
) button and then the / (TAPE 2 ) but-
ton. (If tracks have been stored in memory by programming, recording will restart
from the first track stored in memory.)
from the first track stored in memory.)
Whilst recording, OPEN/CLOSE button is deactivated. It is recommended to
perform CD recording after closing the disc tray.
perform CD recording after closing the disc tray.
1
Press the ON/STAND-BY button to turn the power on.
2
Load a cassette into the TAPE 2 cassette compartment with the
side to be recorded on facing you.
side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be performed.
3
Press the CD button and load the desired disc.
4
Press the DISC SKIP button to select the disc to be recorded first.
5
Press the REC PAUSE (
) button.
Recording will be paused.
6
Press the / (TAPE 2 ) button to start recording.
CD playback will start approximately 7 seconds after the tape starts.
Recording is started from the selected CD. When the playback of the last disc
is finished or the end of the tape is reached, the CD and the cassette will stop
automatically.
is finished or the end of the tape is reached, the CD and the cassette will stop
automatically.
1
Programme discs and tracks. (See page 18.)
2
Press the REC PAUSE (
) button.
3
Press the / (TAPE 2 ) button.
Programmed play (See page 18.)
23
CD-DP900E(UK)_2.fm
02/1/8
CD-DP900E
T
a
p
e
Recor
d
in
g
- Rec
o
rd
in
g
t
o
a ca
sse
tt
e
ta
p
e
-
Recording from the radio
Press the REC PAUSE (
) button.
Press
the
(TAPE )
button.
Note:
Dubbing from tape to tape
You can record from TAPE 1 to TAPE 2.
To stop dubbing:
Press
the
(TAPE )
button.
TAPE 1 and TAPE 2 will simultaneously stop.
Erasing recorded tapes
Note:
Make sure that the TAPE 1 is not in use.
1
Tune in to the desired station. (See page 19.)
2
Load a cassette into the TAPE 2 cassette compartment with the
side to be recorded on facing you.
side to be recorded on facing you.
3
Press the REC PAUSE (
) button.
Recording will be paused.
4
Erase-prevention tab of cassette tapes:
Side A
Tab for side B
Tab for side A
1
Press the ON/STAND-BY button to turn the power on.
2
Load a prerecorded cassette into the
TAPE 1 cassette compartment. Insert
a blank tape into the TAPE 2 cassette
compartment.
TAPE 1 cassette compartment. Insert
a blank tape into the TAPE 2 cassette
compartment.
3
Press the TAPE (1 2) button until
"TAPE 1" appears on the display.
"TAPE 1" appears on the display.
4
Press the REC PAUSE (
) button.
Recording will be paused.
5
Press the / (TAPE 2 ) button to
start dubbing.
start dubbing.
1
Load the tape to be erased into the TAPE 2 cassette compartment with the side to
be erased facing toward you.
be erased facing toward you.
2
Press the TAPE (1 2) button until "TAPE 2" appears on the display.
3
Press the REC PAUSE (
) button.
4
Press the / (TAPE 2 ) button to start erasing.
Tuning (See page 19.)