Read Sharp CD-DP900 (serv.man6) User Guide / Operation Manual online
19
CD-DP900E(UK)_2.fm
02/1/8
CD-DP900E
Ra
dio
- Lis
te
n
ing t
o
the
r
a
dio -
Listening to the radio
Tuning
To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the "ST" indicator.
"
" will appear when an FM broadcast is in stereo.
If the FM reception is weak, press the TUNER (BAND) button to extinguish the
"ST" indicator. The reception changes to monaural, and the sound becomes
clearer.
"ST" indicator. The reception changes to monaural, and the sound becomes
clearer.
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TUNER (BAND) button repeatedly to select the desired
frequency band (FM or AM).
frequency band (FM or AM).
3
Press the TUNING/TIME ( or ) button to tune in to the desired
station.
station.
Manual tuning:
Press the TUNING/TIME button as many times as required to tune in to the de-
sired station.
sired station.
Auto tuning:
When the TUNING/TIME button is pressed for more than 0.5 seconds, scanning
will start automatically and the tuner will stop at the first receivable broadcast sta-
tion.
will start automatically and the tuner will stop at the first receivable broadcast sta-
tion.
Notes:
When radio interference occurs, auto scan tuning may stop automatically at
that point.
that point.
Auto scan tuning will skip weak signal stations.
To stop the auto tuning, press the TUNING/TIME button again.
FM stereo mode indicator
FM stereo receiving indicator
Sound control (See page 14.)
20
CD-DP900E(UK)_2.fm
02/1/8
CD-DP900E
Ra
dio
- Lis
te
n
ing t
o
the
r
a
dio -
Listening to the radio (continued)
Memorising a station
You can store 40 AM and FM stations in memory and recall them at the push of a but-
ton. (Preset tuning)
ton. (Preset tuning)
Note:
The backup function protects the memorised stations for a few hours should there be
a power failure or the AC power lead disconnection.
a power failure or the AC power lead disconnection.
To recall a memorised station
To scan the preset stations
The stations saved in memory can be scanned automatically. (Preset memory scan)
To erase entire preset memory
1
Perform steps 1 - 3 in "Tuning" on page 19.
2
Press the MEMORY/SET button to enter the preset tuning saving
mode.
mode.
3
Within 30 seconds, press the PRESET ( or ) button to select the
preset channel number.
preset channel number.
Store the stations in memory, in order, starting with preset channel 1.
4
Within 30 seconds, press the MEMORY/SET button to store that
station in memory.
station in memory.
If the "MEMORY" and preset number indicators go out before the station is mem-
orised, repeat the operation from step 2.
orised, repeat the operation from step 2.
5
Repeat steps 1 - 4 to set other stations, or to change a preset sta-
tion.
tion.
Press the PRESET ( or ) button for less than 0.5 seconds to select
the desired station.
the desired station.
Preset channel
Frequency and frequency band
This can be operated by pressing the TUNER PRESET ( or ) button on the re-
mote control.
mote control.
1
Press the PRESET ( or ) button for more than 0.5 seconds.
The preset number will flash and the programmed stations will be tuned in se-
quentially, for 5 seconds each.
quentially, for 5 seconds each.
This can be operated by pressing the TUNER PRESET ( or ) button on the
remote control.
remote control.
2
Press the PRESET ( or ) button again when the desired station is located.
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Whilst pressing down the TUNER (BAND) button and the EQUALIZER/X-BASS/
DEMO button, press the ON/STAND-BY button until "TUNER CL" appears.
DEMO button, press the ON/STAND-BY button until "TUNER CL" appears.
Tuning (See page 19.)
Display