Read Sharp CD-DP900 (serv.man3) User Guide / Operation Manual online
10
CD-DP900E(UK)_1.fm
02/1/11
CD-DP900E
Prepara
tion f
o
r U
s
e
- S
y
s
te
m
c
onne
c
tion
s
-
System connections
Removing the transport screw
Before turning the power on, be sure to remove the transport screw on
the back of the unit using a flat head screwdriver or a coin.
the back of the unit using a flat head screwdriver or a coin.
Note:
This screw is required when transporting the unit again. Please keep it (see page 29).
Aerial connection
Note:
Placing the aerial on the stereo system or near the AC power lead may cause noise
pickup. Place the aerial away from the stereo system for better reception.
pickup. Place the aerial away from the stereo system for better reception.
Installing the AM loop aerial:
External FM aerial:
Use an external FM aerial if you require better reception. Consult your dealer.
AM loop aerial
FM aerial
Front speaker
(Left)
Front speaker
(Right)
Transport screw
Wall socket
(AC 230-240 V, 50 Hz)
(AC 230-240 V, 50 Hz)
Surround speaker
(Right)
Surround speaker
(Left)
Centre speaker
Supplied FM aerial:
Connect the FM aerial wire to the FM 75
OHMS socket and position the FM aerial wire
in the direction where the strongest signal can
be received.
OHMS socket and position the FM aerial wire
in the direction where the strongest signal can
be received.
Supplied AM loop aerial:
Connect the AM loop aerial to the AM LOOP
socket. Position the AM loop aerial for opti-
mum reception. Place the AM loop aerial on a
shelf, etc., or attach it to a stand or a wall with
screws (not supplied).
socket. Position the AM loop aerial for opti-
mum reception. Place the AM loop aerial on a
shelf, etc., or attach it to a stand or a wall with
screws (not supplied).
< Assembling >
< Attaching to the wall >
Wall
Screws
(not
supplied)
External FM aerial
11
CD-DP900E(UK)_1.fm
02/1/10
CD-DP900E
Prepara
tion f
o
r U
s
e
- S
y
s
te
m
c
onne
c
tion
s
-
Speaker connection
Front speakers
Connect the black wire to the FRONT (-) terminal, and the red wire to the FRONT (+) terminal.
Centre speaker
Connect the black wire to the CENTER (-) terminal, and the orange wire to the
CENTER (+) terminal.
CENTER (+) terminal.
Surround speakers
Connect the black wire to the SURROUND (-) terminal, and the grey wire to the SUR-
ROUND (+) terminal.
ROUND (+) terminal.
Caution:
Placing the speaker system
To enjoy the surround effect, we recommend that you place each speaker as shown
to the below.
to the below.
Installation of the surround speakers:
If possible, mount the surround speakers on the wall. Install them 60 cm - 90 cm (23"
- 35") above the height of your ears when you are seated.
- 35") above the height of your ears when you are seated.
If you use other speakers with impedance lower than that
specified, the unit may be damaged. Front speakers: 6
ohms Centre speaker: 6 ohms Surround speakers: 12
ohms
specified, the unit may be damaged. Front speakers: 6
ohms Centre speaker: 6 ohms Surround speakers: 12
ohms
Do not mistake the right and the left channels. The right
speaker is the one on the right side when you face the unit.
speaker is the one on the right side when you face the unit.
Do not let the bare speaker wires touch each other.
Do not allow any objects to fall into or to be placed in the
bass reflex ducts.
bass reflex ducts.
Do not stand or sit on the speakers. You may be injured.
Incorrect
Black
Red
Front speaker (Right)
Surround speaker (Right)
Surround speaker (Left)
Front speaker (Left)
Grey
Orange
Centre speaker
Notes:
The front speakers and the centre speaker are magnetically shielded.
Therefore, they do not affect the display even you use them near the TV. However,
some colour variation may occur, depending on the type of TV used.
Therefore, they do not affect the display even you use them near the TV. However,
some colour variation may occur, depending on the type of TV used.
If colour variation occurs...
Turn off the TV (from the power switch).
After 15 - 30 minutes, turn the TV on again.
After 15 - 30 minutes, turn the TV on again.
If the colour variation is still present...
Move the front speakers further away from the TV.
If any kind of magnet or an electromagnet is placed too close to the TV and the sys-
tem, irregular colours may appear on the TV screen.
tem, irregular colours may appear on the TV screen.
Main unit
Centre speaker
Front speaker
(Left)
(Left)
Front speaker
(Right)
(Right)
Surround speaker
(Left)
(Left)
Surround speaker
(Right)
(Right)
TV
Wall
Example: when installed on the wall
Example: when installed vertically
60 - 90 cm
(23" - 35")
(23" - 35")
12
CD-DP900E(UK)_1.fm
02/1/10
CD-DP900E
Prepara
tion f
o
r U
s
e
- S
y
s
te
m
c
onne
c
tion
s
-
System connections (continued)
To mount the surround speakers on the
wall
wall
The design of the surround speakers allows them to be hung on the wall. Be sure to
use the type and size of screw that is shown to the below.
use the type and size of screw that is shown to the below.
Connecting the AC power lead
After checking all the connections have been made correctly, plug the AC power lead
of this unit into the wall socket. If you plug in the unit first, the unit will enter the dem-
onstration mode.
of this unit into the wall socket. If you plug in the unit first, the unit will enter the dem-
onstration mode.
Notes:
The unit will start the tape initialisation when plugged in to the AC socket. During
this process, initialising sound will be heard and the unit cannot be turned on. Wait
until the process is finished.
this process, initialising sound will be heard and the unit cannot be turned on. Wait
until the process is finished.
Unplug the AC power lead from the wall socket if the unit will not be in use for a
prolonged period of time.
prolonged period of time.
Headphones
1
Make a hole in the wall using a
drill.
drill.
2
Drive a wall mount plug into the
hole using a hammer. Drive the
wall mount plug in until it is flush
with the wall surface.
hole using a hammer. Drive the
wall mount plug in until it is flush
with the wall surface.
3
Drive one screw into the wall
mount plug for each speaker.
mount plug for each speaker.
Drive the screws, so there is about a 5
mm (3/16") space between the wall and
the head of the screw.
mm (3/16") space between the wall and
the head of the screw.
4
Mount the surround speaker on
the wall so that the screw head is
inserted into the slot on the sur-
round speaker.
the wall so that the screw head is
inserted into the slot on the sur-
round speaker.
5 mm (3/16")
3.2 mm (1/8")
Min. 22 mm (7/8")
9 mm (3/8")
32 mm (1-1/4")
8 - 9 mm (3/8")
Wall mounting screw
Wall surface
Wall surface
Before plugging in or unplugging the headphones,
reduce the volume.
reduce the volume.
Be sure your headphones have a 3.5 mm (1/8") di-
ameter plug and are between 16 ohms and 50
ohms impedance. The recommended impedance
is 32 ohms.
ameter plug and are between 16 ohms and 50
ohms impedance. The recommended impedance
is 32 ohms.
Plugging in the headphones disconnects the
speakers automatically. Adjust the volume using
the VOLUME buttons.
speakers automatically. Adjust the volume using
the VOLUME buttons.
13
CD-DP900E(UK)_1.fm
02/1/11
CD-DP900E
Prepara
tion f
o
r U
s
e
-
S
y
s
te
m
c
onne
c
ti
o
ns
/ Re
mo
te
c
ont
ro
l -
Demonstration mode
To cancel the demonstration mode:
When the unit is in the power stand-by mode (demonstration mode), press the
EQUALIZER/X-BASS/DEMO button. The demonstration mode will be cancelled and
the display will disappear.
EQUALIZER/X-BASS/DEMO button. The demonstration mode will be cancelled and
the display will disappear.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the EQUALIZER/X-BASS/DEMO
button again.
button again.
Note:
When the power is on, the EQUALIZER/X-BASS/DEMO button can be used to select
the extra bass mode.
the extra bass mode.
To turn the power on
Press the ON/STAND-BY button to turn the power on.
To set the unit to stand-by mode:
Press the ON/STAND-BY button again.
Remote control
Battery installation
Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
Batteries are not included.
Precautions for battery use:
Replace all old batteries with new ones at the same time.
Do not mix old and new batteries.
Remove the batteries if the unit is not to be used for long periods of time. This will
prevent potential damage due to battery leakage.
prevent potential damage due to battery leakage.
Caution:
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
Installing the batteries incorrectly may cause the unit to malfunction.
Notes concerning use:
Replace the batteries if the operating distance is reduced or if the operation
becomes erratic.
becomes erratic.
Periodically clean the transmitter on the remote control and the sensor on the unit
with a soft cloth.
with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with operation.
Change the lighting or the direction of the unit.
Change the lighting or the direction of the unit.
Keep the remote control away from moisture, heat, shock, and vibrations.
Test of the remote control
The first time the unit is plugged in, the unit will
enter the demonstration mode. You will see
words scroll.
enter the demonstration mode. You will see
words scroll.
1 Remove the battery cover.
2 Insert the batteries according to the direction indicated in the bat-
2 Insert the batteries according to the direction indicated in the bat-
tery compartment.
When inserting or removing the batteries, push them towards the battery terminals.
3 Replace the cover.
Point the remote control directly at the remote
sensor on the unit.
sensor on the unit.
The remote control can be used with-
in the range shown:
in the range shown:
Press the ON/STAND-BY button. Does the pow-
er turn on? Now, you can enjoy the music.
er turn on? Now, you can enjoy the music.
0.2 m - 6 m
(8" - 20')
(8" - 20')
Remote sensor
