Read Sharp CD-C3H (serv.man6) Service Manual online
CD-C3H/CP-C3H
– 7 –
OPERATION MANUAL
S
E
TTING
THE
CLO
CK
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Press the CLOCK button.
3
Within 5 seconds, press the MEMORY/SET button.
4
Turn the jog dial to select the time display mode.
0:00
AM
12:00
0:00
AM
3
4
5
6
7
8
9
MEMORY/
SET
ON/STAND-
BY
CLOCK
"0
:0
0
"
→
Th
e 2
4
-h
ou
r dis
pl
ay
w
ill a
p
p
e
a
r.
(
0
:0
0
-
2
3
:5
9
)
"AM 12:00"
→
Th
e 1
2
-h
ou
r di
sp
lay
w
ill
ap
pe
ar
.
(
A
M
o
r P
M
1
2
:0
0
-
1
1
:5
9
)
"A
M
0:
00
"
→
T
h
e 1
2
-h
ou
r di
sp
la
y
w
ill
ap
pe
ar
.
(
A
M
o
r P
M
0
:0
0
-
1
1
:5
9
)
●
Note that this can only be set when the unit is first installed
or it has been reset.
5
Press the MEMORY/SET button.
6
Adjust the hour by turning the jog dial.
●
Turn the dial one click to advance the time by 1 hour.
Keep turning the dial to advance continuously.
●
When the 12-hour display is selected, "AM" will change auto-
matically to "PM".
7
Press the MEMORY/SET button.
8
Adjust the minutes by turning the jog dial.
●
Turn the dial one click to advance the time by 1 minute.
Keep turning the dial to advance continuously.
●
The hour setting will not advance even if minutes advance
from "59" to "00".
9
Press the MEMORY/SET button.
●
The clock starts operating from "0" seconds. (Seconds are
not displayed.)
Note:
●
In the event of a power failure or when the AC power lead
is disconnected, the clock display will go out.
When the AC power supply is restored, the clock display will
flash on and off to indicate the time when the power failure
occurred or when the AC power lead was disconnected.
If this happens, follow the procedure below to change the
clock time.
To change the clock time:
When the unit is in the stand-by mode:
①
Press the MEMORY/SET button.
②
Perform steps 6 - 9 above.
When the unit is on:
①
Press the CLOCK button.
②
Within 5 seconds, press the MEMORY/SET button.
③
Perform steps 6 - 9 above.
To see the time display:
Press the CLOCK button.
●
The time display will appear for about 5 seconds.
To change the time display mode:
①
Perform steps 1 - 2 in the section "RESETTING THE MICRO-
COMPUTER", on page 31 of Operation Manual.
②
Perform steps 1 - 9 above.
In this example, the clock is set for the 24-hour
(0:00) system.
Jog dial
2
PREPARATION FOR USE
■
Remote control
Notes concerning use:
●
Replace the batteries if control distance decreases or oper-
ation becomes erratic.
●
Periodically clean the transmitter LED on the remote control
and the sensor on the main unit with a soft cloth.
●
Exposing the sensor on the main unit to strong light may
interfere with operation. Change the lighting or the direction
of the unit.
●
Keep the remote control away from moisture, excessive heat,
shock, and vibrations.
15
15
0.2 m - 6 m
(8" - 20')
RE
S
E
TTI
NG
THE
MI
CRO
CO
MP
UTE
R
Reset the microcomputer under the following conditions:
●
To erase all of the stored memory contents (clock and timer
settings, and tuner and CD presets).
●
If the display is not correct.
●
If the operation is not correct.
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Press and hold down the
button, the EQ/DEMO button
and the ON/STAND-BY button all at the same time. Hold
them for at least 1 second.
Caution:
●
The operation explained above will erase all data stored in
memory including clock and timer settings, and tuner and CD
presets.
1,2
2
WHE
N "
P
RO
TE
CT"
AP
P
E
ARS
The unit will be overheated when "PROTECT" appears in the
display.
Due to the problem in speaker circuit the unit will be switched
to the stand-by mode automatically.
In this case take the following corrective actions.
1
Unplug the AC power plug from the AC socket.
2
Make sure that the unit vent is not blocked.
3
Make sure that the speaker wires have been correctly con-
nected to the speaker terminals.
4
After checking items 2 and 3 above, wait for 2 or 3 hours
before trying to use the unit.
5
Reconnect the AC power lead.
Note:
●
If "PROTECT" appears again during use, please unplug the
AC power plug, and contact the SHARP authorised service
centre.
Click on the first or last page to see other CD-C3H (serv.man6) service manuals if exist.