Read Sharp CD-BA250 (serv.man11) Specification online
– 3 –
CD-BA250H/CD-BA2600H
General
Amplifier (Except for U.K.)
CD player
Tuner
Cassette deck (Except for U.K.)
Power source
AC 230 V, 50 Hz
Power consumption
Power on: 124 W
Power stand-by: 0.6 W (*)
Dimensions
Width: 270 mm (10-5/8")
Height: 330 mm (13")
Depth: 340 mm (13-3/8")
Height: 330 mm (13")
Depth: 340 mm (13-3/8")
Weight
6.7 kg (14.7 lbs.)
( * )
This power consumption value is obtained when the demonstration mode is
cancelled in the power stand-by mode. cancel the demonstration mode.
cancelled in the power stand-by mode. cancel the demonstration mode.
Output power
PMPO: 480 W
MPO: 240 W (120 W + 120 W) (DIN 45 324)
RMS: 150 W (75 W + 75 W) (DIN 45 324)
RMS: 104 W (52 W + 52 W) (DIN 45 500)
Output terminals
Speakers: 6 ohms
Headphones: 16 - 50 ohms (recommended: 32 ohms)
Input terminals
Video/Auxiliary (audio signal): 500 mV/47 kohms
Type
3-disc multi-play compact disc player
Signal readout
Non-contact, 3-beam semiconductor laser pickup
D/A converter
1-bit D/A converter
Frequency response
20 - 20,000 Hz
Dynamic range
90 dB (1 kHz)
Frequency range
FM: 87.5 - 108 MHz
AM: 522 - 1,620 kHz
Frequency response
50 - 14,000 Hz (Normal tape)
Signal/noise ratio
Wow and flutter
0.35 % (DIN 45 511)
Type
5 cm (2") Tweeter
13 cm (5-1/4") Woofer
Maximum input power
150 W
Rated input power
75 W
Impedance
6 ohms
Dimensions
Width: 220 mm (8-11/16")
Height: 330 mm (13")
Depth: 217 mm (8-9/16")
Height: 330 mm (13")
Depth: 217 mm (8-9/16")
Weight
3.0 kg (6.6 lbs.)/each
Amplifier (CD-BA250H for U.K.)
Cassette deck (CD-BA250H for U.K.)
Output power
RMS: 150 W (75 W + 75 W) (10 % T.H.D.)
RMS: 104 W (52 W + 52 W) (0.9 % T.H.D.)
Output terminals
Speakers: 6 ohms
Headphones: 16 - 50 ohms (recommended: 32 ohms)
Input terminals
Video/Auxiliary (audio signal): 500 mV/47 kohms
Frequency response
50 - 14,000 Hz (Normal tape)
Signal/noise ratio
Wow and flutter
0.3 % (WRMS)
SPECIFICATIONS
CD-BA250H/CD-BA2600H
IMPORTANT SERVICE NOTES (CD-BA250H FOR U.K. ONLY)
Before returning the unit to the customer after completion of a
repair or adjustment it is necessary for the following withstand
voltage test to be applied to ensure the unit is safe for the
customer to use.
Setting of Withstanding Voltage Tester and set.
repair or adjustment it is necessary for the following withstand
voltage test to be applied to ensure the unit is safe for the
customer to use.
Setting of Withstanding Voltage Tester and set.
Set name
set value
Withstanding Voltage Tester
Test voltage
4,240 VPEAK
3,000 VRMS
3,000 VRMS
Set time
6 secs
Set current (Cutoff current)
4 mA
Unit
Judgment
OK: The “GOOD” lamp lights.
NG: The “NG” lamp lights and the buzzer sounds.
NG: The “NG” lamp lights and the buzzer sounds.
SHORT-CIRCUIT
AC POWER
SUPPLY CORD
AC POWER
SUPPLY CORD
CONNECT THE PROBE
TO GND
TO GND
OF CHASSIS
SCREW
PROBE
AC
UNIT
WITHSTANDING
VOLTAGE TESTER
VOLTAGE TESTER
+
-
OUT
CHASSIS SCREW
CP-BA250H/CP-BA2600H
Display