CD-BA2010. part (from the ) - Sharp Audio User Guide / Operation Manual

cd-ba2010 user guide / operation manual
Model
CD-BA2010
Pages
1 Few pages! See other manuals at the bottom of the first or last page.
Size
63.09 KB
Type
PDF
Document
User Guide / Operation Manual
Brand
Device
Audio / System / part (from the )
File
cd-ba2010.pdf
Date

Read Sharp CD-BA2010 User Guide / Operation Manual online

CD-BA2010H
– 6 –
OPERATION MANUAL
SETTING THE CLOCK
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Press the CLOCK button.
3
Within 5 seconds, press the MEMORY/SET button.
4
Press theTUNING/TIME (      or      ) button to select the time 
display mode.
“0:00”
The 24-hour display will appear.
(0:00 - 23:59)
“AM 0:00”
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
“AM 12:00”
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
Note that this can only be set when the unit is first in-
stalled or it has been reset.
5
Press the MEMORY/SET button.
6
Press the TUNING/TIME (      or      ) button to adjust the hour. 
Press the TUNING/TIME (      or      ) button once to ad- 
vance 
the time by 1 hour
. Hold it down to advance con-
tinuously
.
When the 12-hour display is selected, “AM” will change
automatically to 
“PM”.
7
Press the MEMOR
Y/SET
 button.
8
Press the 
TUNING/TIME (
 or 
) button to adjust the min-
utes.
Press the 
TUNING/TIME (
 or 
) button once to ad-
vance 
the time by 1 minute. Hold it down to change the
time in 5 
minute intervals.
The hour setting will not advance even if minutes advance
from “59” to “00”.
9
Press the MEMOR
Y/SET
 button.
The clock starts operating from “0” second.
(Seconds are not displayed.)
And then the clock display will disappear after a few sec-
onds.
T
o
 see the time display:
Press the CLOCK button.
The time display will appear for about 5 seconds.
Note:
The clock display will flash on and of
f at the push of the
CLOCK button when the 
a power failure occurs or after the 
AC power lead is discon-
nected.
If this happens, follow the procedure below to change the
clock time.
T
o
 change the clock time:
 1
Press the CLOCK button.
 2
Within 5 seconds, press the MEMOR
Y/SET
 button.
 3
Perform steps 6 - 9 above.
T
o
 change the time display mode:
 1
Perform steps 1 - 2 in the section “RESETTING 
THE
MICROCOMPUTER”.
 2
Perform steps 1 - 9 above.
(Main unit operation)
REMOTE CONTROL
0.2 m - 6 m
(8" - 20’)
Notes concerning use:
Replace the batteries if the operating distance is reduced or
if the operation becomes erratic.
Periodically clean the transmitter LED on the remote con-
trol and the sensor on the main unit with a soft cloth.
Exposing the sensor on the main unit to strong light may
interfere with operation. Change the lighting or the direction
of the unit.
Keep the remote control away from moisture, excessive heat,
shock, and vibrations.
RESETTING THE MICROCOMPUTER
Reset the microcomputer under the following con-
ditions:
T
o
settings, and tuner and CD presets).
If the display is not correct.
If the operation is not correct.
1
Press the ON/ST
AND-BY
 button to enter the stand-by mode.
2
Whilst pressing down the 
/
 button and the X-BASS/
DEMO 
button, hold down the ON/ST
AND-BY
 button for at
least 1 second.
“CLEAR 
AL” will appear
.
Caution:
memory including clock and timer settings, and tuner and
CD presets.
Display

Download Sharp CD-BA2010 User Guide / Operation Manual

Here you can read online and download Sharp CD-BA2010 User Guide / Operation Manual in PDF. CD-BA2010 user guide / operation manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp CD-BA2010 System. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.