TY-42TM5H, TY-37TM5H - Panasonic TV Service Manual (repair manual)

ty-42tm5h, ty-37tm5h service manual
Model
TY-42TM5H TY-37TM5H
Pages
10
Size
801.87 KB
Type
PDF
Document
Service Manual
Brand
Device
TV
File
ty-42tm5h-ty-37tm5h.pdf
Date

Read Panasonic TY-42TM5H / TY-37TM5H Service Manual online

TY-42TM5H
TY-37TM5H
Tuner Terminal Board
ORDER NO. ITD0207023C2
1 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
3
2 About lead free solder (PbF)
4
3 Conductor Views
5
3.1. H-Board (TY-37/42TM5H)
5
4 Block and Schematic Diagrams
7
4.1. Schematic Diagram Notes
7
4.2. H-Board (TY-37/42TM5H) Block and Schematic Diagrams
8
5 Replacement Parts List
9
5.1. Replacement Parts List Notes
9
5.2. Replacement Parts List
10
CONTENTS
Page
Page
2
TY-42TM5H / TY-37TM5H
1 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alminum
foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, alminum foil or comparable
conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing
together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to
damage an ES device).
3
TY-42TM5H / TY-37TM5H
2 About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d
suggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol
stamped on the back of PCB.
Caution
 ·
Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70
F (30~40
C) higher.
Please use a high temperature soldering iron and set it to 700 ± 20
F (370 ± 10
C).
 ·
Pb free solder will tend to splash when heated too high (about 1100
F or600
C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb
solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
 ·
After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto
the opposite side. (see figure below)
Suggested Pb free solder
There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder.
However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
4
TY-42TM5H / TY-37TM5H
Page of 10
Display

Download Panasonic TY-42TM5H / TY-37TM5H Service Manual (Repair Manual)

Here you can read online and download Panasonic TY-42TM5H / TY-37TM5H Service Manual in PDF. TY-42TM5H / TY-37TM5H service manual will guide through the process and help you recover, restore, fix, disassemble and repair Panasonic TY-42TM5H / TY-37TM5H TV. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.