TX-28PK10 - Panasonic TV Service Manual (repair manual)

tx-28pk10 service manual
Model
TX-28PK10
Pages
46
Size
5.25 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / EURO-5L
File
tx-28pk10.pdf
Date

Read Panasonic TX-28PK10 Service Manual online

Service Support
Service and repair of this
product is supported by
Panasonic's LUCI interface.
This interface provides
a link between the TV and
a standard PC to ow a
number of diagnostic and
control functions to be
performed.
For more details contact
your local Panasonic company.
TX-28PK10 Service Manual
Specifications
Parts List
Safety
Block
Diagrams
Exploded
View
PCB
Views
Service
Information
Schematic
Diagrams
BACK
EXIT
6HUYLFH0DQXDO
Colour Television
TX-28PK10
EURO-5L Chassis
SPECIFICATIONS
Power Source:
220-240V a.c., 50Hz
Power Consumption:
142W
Stand-by Power
Consumption:
1.4W
Aerial Impedance:
75
 unbalanced, Coaxial Type
Receiving System:
PAL I, PAL-525/60
M.NTSC
NTSC (AV only)
Receiving Channels:
UHF E21-E69
Intermediate Frequency:
Video/Audio
Video
39.5MHz
Audio
33.5MHz
32.95MHz (NICAM)
Colour
35.07MHz
Terminals:
AV1 IN
Video (21 pin)
1V p-p 75
Audio (21 pin)
500mV rms 10k
RGB (21 pin)
AV1 OUT
Video (21 pin)
1V p-p 75
Audio (21 pin)
500mV rms 1k
AV2 IN
Video (21 pin)
1V p-p 75
Audio (21 pin)
500mV rms 10k
S-Video IN
Y: 1V p-p 75
(21-pin)
C: 0.3V p-p 75
AV2 OUT
Video (21 pin)
1V p-p 75
Audio (21 pin)
500mV rms 1k
Selectable output (21 pin)
AV3 IN
S-Video IN
Y: 1V p-p 75
(4-pin)
C: 0.3V p-p 75
Audio (RCAx2)
500mV rms 10k
Video (RCAx1)
1V p-p 75
AV4 IN
Video (21 pin)
1V p-p 75
Audio (21 pin)
500mV rms 10k
S-Video IN
Y: 1V p-p 75
(21-pin)
C: 0.3V p-p 75
AV4 OUT
Video (21 pin)
1V p-p 75
Audio (21 pin)
500mV rms 1k
High Voltage:
30.5kV 
±
 1kV
Picture Tube:
W66LQK185X05 66cm
Audio Output:
Front Left/Right
2 x 20W
(Music Power)
Headphones:
8
 Impedance
3.5mm
Accessories
supplied:
Remote Control
2 x R6 (UM3) Batteries
VS-PK1/2 Video Cabinet
Dimensions:
Height:
503mm
Width:
720mm
Depth:
527mm
Net weight:
44kg
Specifications are subject to change without notice.
Weights and dimensions shown are approximate.
NOTE: This Service Manual should be used in conjunction with
the EURO-5L Technical guide.
ORDER No. SM-99096
Panasonic CS ( U.K. ) Ltd.
WILLOUGHBY ROAD,
BRACKNELL,
BERKS.,
RG12 8FT.
CONTENTS
SAFETY PRECAUTIONS..........................................................................................................................................................2
SERVICE HINTS .......................................................................................................................................................................3
SERVICE POSITION.................................................................................................................................................................4
ADJUSTMENT PROCEDURE AND FACTORY SETTINGS .....................................................................................................5
WAVEFORM PATTERN TABLE ...............................................................................................................................................6
ALIGNMENT SETTINGS...........................................................................................................................................................7
BLOCK DIAGRAMS ..................................................................................................................................................................8
PARTS LOCATION .................................................................................................................................................................12
REPLACEMENT PARTS LIST ................................................................................................................................................13
SCHEMATIC DIAGRAMS .......................................................................................................................................................28
CONDUCTOR VIEWS.............................................................................................................................................................35
SAFETY PRECAUTIONS
GENERAL GUIDE LINES
1.  It is advisable to insert an isolation transformer in the
a.c. supply before servicing a hot chassis.
2.  When servicing, observe the original lead dress in the
high voltage circuits. If a short circuit is found, replace
all parts that have been overheated or damaged by
the short circuit.
3.  After servicing, see that all the protective devices
such as insulation barriers, insulation papers, shields
and isolation R-C combinations are correctly
installed.
4.  When the receiver is not being used for a long period
of time, unplug the power cord from the a.c. outlet.
5.  Potentials as high as 31.5kV are present when this
receiver is in operation. Operation of the receiver
without the rear cover involves the danger of a shock
hazard from the receiver power supply. Servicing
should not be attempted by anyone who is not
familiar with the precautions necessary when working
on high voltage equipment. Always discharge the
anode of the tube.
6.  After servicing make the following leakage current
checks to prevent the customer from being exposed
to shock hazard.
LEAKAGE CURRENT COLD CHECK
1.  Unplug the a.c. cord and connect a jumper between
the two prongs of the plug.
2.  Turn on the receiver’s power switch.
3.  Measure the resistance value with an ohmmeter,
between the jumpered a.c. plug and each exposed
metallic cabinet part on the receiver, such as screw
heads, aerials, connectors, control shafts etc. When
the exposed metallic part has a return path to the
chassis, the reading should be between 4M ohm and
20M ohm. When the exposed metal does not have a
return path to the chassis, the reading must be
infinite.
LEAKAGE CURRENT HOT CHECK
1.  Plug the a.c. cord directly into the a.c. outlet. Do not
use an isolation transformer for this check.
2. Connect 
2k
 10W resistor in series with an
exposed metallic part on the receiver and an earth,
such as a water pipe.
3.  Use an a.c. voltmeter with high impedance to
measure the potential across the resistor.
4.  Check each exposed metallic part and check the
voltage at each point.
5.  Reverse the a.c. plug at the outlet and repeat each of
the above measurements.
6.  The potential at any point should not exceed
1.4Vrms. In case a measurement is outside the limits
specified, there is a possibility of a shock hazard, and
the receiver should be repaired and rechecked before
it is returned to the customer.
X-RADIATION WARNING
1.  The potential sources of X-Radiation in TV sets are
the high voltage section and the picture tube.
2.  When using a picture tube test jig for service, ensure
that the jig is capable of handling 31.5kV without
causing X-Radiation.
NOTE:
 It is important to use an accurate periodically
calibrated high voltage meter.
1.  Set the brightness to minimum.
2.  Measure the high voltage. The meter should indicate.
30.5kV  ± 1kV.
If the meter indication is out of tolerance, immediate
service and correction is required to prevent the
possibility of premature component failure.
3.  To prevent any X-Radiation possibility, it is essential
to use the specified tube.
HOT CHECK CIRCUIT
a.c. VOLTMETER
WATER PIPE
(EARTH)
TO INSTRUMENT’S EXPOSED
METALLIC PARTS
Fig. 1
2k
 10 Watts
2
SERVICE HINTS
How to remove the rear cover
1. Remove the 9 screws as shown in 
Fig. 2
.
LOCATION OF CONTROLS
3
Y-Board
Focus
Screen
Fig. 3
Fig. 2
SCREWS
SCREWS
M-Board
Z-Board
G-Board
F-Board
H-Board
E-Board
D-Board
Q-Board
Page of 46
Display

Download Panasonic TX-28PK10 Service Manual (Repair Manual)

Here you can read online and download Panasonic TX-28PK10 Service Manual in PDF. TX-28PK10 service manual will guide through the process and help you recover, restore, fix, disassemble and repair Panasonic TX-28PK10 TV. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.