Read Panasonic TX-28MK1CM Service Manual online
ADJUSTMENT PROCEDURE
Item/Preparation
Adjustments
+B SET-UP
1. Receive a Greyscale signal.
2. Set the controls:-
2. Set the controls:-
Brightness
Minimum
Contrast
Minimum
Volume
Minimum
1. Set the +B voltage up as follows:-
Adjust R811 so that B2 shows 148V±1V
2. Confirm the following voltages.
B9
5
±
0,25V B10
5
±
0,25V
B5
12
±
0,5V
B11
33 ±
1,5V
B4
16
±
1V
B7
8
±
0,5V
B12 26
±
1V
B8
5,5 ±
0,5V
B3
35
±
1V
B13
15 ±
1V
B1
200
±
10V
B14
-15 ±
1V
Cut-Off / Ug2 Test
1. Receive
a
Greyscale
signal.
2. Degauss the tube externally.
3. Set the TV into Service Mode 1.
4. Select Cutoff mode.
3. Set the TV into Service Mode 1.
4. Select Cutoff mode.
To adjust Cutoff connect an oscilloscope to the Blue
cathode, adjust "cutoff" value using the "Yellow" and
"Blue" buttons until the black level is 160V±5V press
"STR" to store the value. Remove the oscilloscope.
Select Ug2 adjustment and adjust the screen VR until the
display shows "O.K."
cathode, adjust "cutoff" value using the "Yellow" and
"Blue" buttons until the black level is 160V±5V press
"STR" to store the value. Remove the oscilloscope.
Select Ug2 adjustment and adjust the screen VR until the
display shows "O.K."
ABGLEICH
Vorbereitungen
Abgleich
+B - Abgleich
1. Testbild
empfangen.
Helligkeit auf Minimum
Kontrast auf Minimum
Lautstärke
Minimum
1. Mit
R811 muß die B2 auf 148V±1V eingestellt
werden.
2. Folgende Spannungen sind zu überprüfen.
B9
5
±
0,25V B10
5
± 0,25V
B5
12
±
0,5V
B11
33
± 1,5V
B4
16
±
1V
B7
8
± 0,5V
B12 26
±
1V
B8
5,5
±
0,5V
B3
35
±
1V
B13
15
± 1V
B1
200
±
10V
B14
-15
± 1V
Cut-Off / Ug2 Test
1. Testbild
empfangen.
2. Bildröhre
entmagnetisieren.
3. Service-Mode 1 anwählen.
4. Im Service-Mode den Abgleichpunkt Cutoff DC-Mode
4. Im Service-Mode den Abgleichpunkt Cutoff DC-Mode
wählen.
Einen Oszillographen an die blaue Katode der Bildröhre
anschliessen. Mit der gelben und blauen Taste den
CUT-OFF Wert auf 160V±5V abgleichen und mit der
STR-Taste abspeichern. Den Oszillograph entfernen und
den Ug2 Test aufrufen. Den Abgleichwert solange
ändern, bis OK auf dem Bildschirm erscheint. Den Wert
abspeichern.
anschliessen. Mit der gelben und blauen Taste den
CUT-OFF Wert auf 160V±5V abgleichen und mit der
STR-Taste abspeichern. Den Oszillograph entfernen und
den Ug2 Test aufrufen. Den Abgleichwert solange
ändern, bis OK auf dem Bildschirm erscheint. Den Wert
abspeichern.
6
Click on the first or last page to see other TX-28MK1CM service manuals if exist.