Read Panasonic TX-21RX20T Service Manual online
2.3. Adjustment for White Balance
Preparation:
1. Receive the white balance pattern and aging should be performed over 30 minutes.
2. Set the picture menu to DYNAMIC NORMAL.
3. Degausse the CRT face.
4. Fix the CRT colour analyzer receiver unit to CRT face.
1. Receive the white balance pattern and aging should be performed over 30 minutes.
2. Set the picture menu to DYNAMIC NORMAL.
3. Degausse the CRT face.
4. Fix the CRT colour analyzer receiver unit to CRT face.
Adjustment of Low Light
1. Adjustment Sub Bright, so that Y = 6.5 ± 1.0 nit.
2. Adjustment R-CUT OFF, so that X = 0.241 ± 0.005 nit.
3. Adjustment G-CUT OFF, so that Y = 0.242 ± 0.005 nit.
1. Adjustment Sub Bright, so that Y = 6.5 ± 1.0 nit.
2. Adjustment R-CUT OFF, so that X = 0.241 ± 0.005 nit.
3. Adjustment G-CUT OFF, so that Y = 0.242 ± 0.005 nit.
Adjustment of High Light
1. Adjustment Sub Bright, so that Y = 150 nit.
2. Adjustment R-Drive, so that X = 0.263 ± 0.003 nit.
3. Adjustment B-Drive, so that Y = 0.261 ± 0.003 nit.
1. Adjustment Sub Bright, so that Y = 150 nit.
2. Adjustment R-Drive, so that X = 0.263 ± 0.003 nit.
3. Adjustment B-Drive, so that Y = 0.261 ± 0.003 nit.
2.4. Adjustment for CRT CUT OFF
Preparation:
1. Connect the oscilloscope probe to TPL5.
2. Screen VR min.
3. Set the data Sub Bright, Bright.
4. In service Mode at “Bright” dac press [5] in factory mode to enter vertical line and adjust by volume down or up button.
5. Adjust “Screen VR” until 1-H Line appears.
1. Connect the oscilloscope probe to TPL5.
2. Screen VR min.
3. Set the data Sub Bright, Bright.
4. In service Mode at “Bright” dac press [5] in factory mode to enter vertical line and adjust by volume down or up button.
5. Adjust “Screen VR” until 1-H Line appears.
2.5. Adjustment Procedure
2.5.1. +B Voltage
Item / preparation
1. Operate the TV set.
2. Set control as follows :
1. Operate the TV set.
2. Set control as follows :
Brightness ........... minimum
Contrast ............... minimum
Contrast ............... minimum
Adjustment procedure
1. Confirm the DC voltage at the indicated test points, as follows :
1. Confirm the DC voltage at the indicated test points, as follows :
TPA 15 : 3.35 ± 0.2 V
TPA 16 : 130 ± 2 V
TPA 17 : 8.25 ± 0.35 V
TPA 18 : 1.85 ± 0.15 V
TPA 19 : 5.30 ± 0.2 V
TPA 20 : 188 ± 15 V
TPA 16 : 130 ± 2 V
TPA 17 : 8.25 ± 0.35 V
TPA 18 : 1.85 ± 0.15 V
TPA 19 : 5.30 ± 0.2 V
TPA 20 : 188 ± 15 V
7
TX-21RX20T
Click on the first or last page to see other TX-21RX20T service manuals if exist.