Read Panasonic TC-M21K / TC-M14K Other Service Manuals online
TQB8E2881---1
Operating
Instructions
TC--M21K
TC--M14K
Important Note :
The layout of the mains plug used
may differ from this illustration.
2
Dear Panasonic Customer,
Welcome to the Panasonic family of customers. We hope that you have many years of enjoyment from your new monitor. The best way to
understand the features of this monitor is to read this book thoroughly, before operating the monitor.
D
This monitor is designed to operate on A.C. 220 --- 240V,
50Hz.
D
Do not expose this monitor to rain, dripping, splashing or
excessive moisture. Ensure that no objects filled with
liquids, such as vases, are placed on the monitor.
D
WARNING: HIGH VOLTAGE !
Do not remove the rear cover, there are no user serviceable
parts inside.
D
Avoid exposing the monitor to direct sunlight or other
sources of heat. Ensure that no naked flame sources, such
as lighted candles, are placed on the monitor.
D
Remove the mains plug from the wall socket when the
monitor is not to be used for a prolonged period of time. Do
not pull the power cable to remove the mains plug from the
socket, always remove it by the plug.
D
CABINET AND PICTURE TUBE CARE
Remove the mains plug from the wall socket. The cabinet and
picture tube can be cleaned with a soft cloth moistened with
mild detergent and water. Do not use solutions containing
benzol or petroleum. Monitors can produce static electricity,
care must be taken whenever touching the monitor screen.
D
Adequate ventilation is essential to prevent failure of electrical
components. We recommend that a gap of at least 5cm is left
all around this monitor even when it is placed inside a cabinet
or between shelves.
FOR YOUR SAFETY PLEASE READ THE FOLLOWING CAREFULLY
WARNING --- THIS APPLIANCE MUST BE EARTHED
This appliance is supplied with a fitted three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. If the
fuse is replaced then the replacement fuse must be 5 amp rated and should be approved by ASTA or BSI to BS1362.
Check for the ASTA mark
or the BSI mark
on the body of the fuse.
If the fitted plug has a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug
must not be used until a replacement cover is obtained. Replacement fuse covers can be purchased through your local Panasonic dealer.
The plug fitted to this appliance incorporates a mains filter circuit. If this is removed or
replaced with a non---filtered mains plug this monitor will no longer meet the European
standards for Electromagnetic Compatibility (EMC). If the fitted plug is unsuitable for
the socket outlet in your home an appropriate adapter should be used.
Nonetheless, if the fitted plug is replaced, the fuse should be taken out and the cut---off
plug disposed of safely. There is danger of severe electrical shock if the cut off plug is
inserted into any 13amp socket.
If a new plug is to be fitted please observe the wiring code as shown below.
The plug fitted to this appliance incorporates a mains filter circuit. If this is removed or
replaced with a non---filtered mains plug this monitor will no longer meet the European
standards for Electromagnetic Compatibility (EMC). If the fitted plug is unsuitable for
the socket outlet in your home an appropriate adapter should be used.
Nonetheless, if the fitted plug is replaced, the fuse should be taken out and the cut---off
plug disposed of safely. There is danger of severe electrical shock if the cut off plug is
inserted into any 13amp socket.
If a new plug is to be fitted please observe the wiring code as shown below.
If in any doubt please consult a qualified electrician.
How to replace the fuse :
How to replace the fuse :
Lift out the removable fuse compartment with a screwdriver and replace the fuse, then refit
securely into the mains plug.
IMPORTANT :--- The wires in the mains lead of this appliance are coloured in accordance with the following code :
IMPORTANT :--- The wires in the mains lead of this appliance are coloured in accordance with the following code :
GREEN & YELLOW : EARTH
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead of this appliance may not correspond to the markings identifying the terminals in your plug,
proceed as follows :---
1.
proceed as follows :---
1.
The
GREEN & YELLOW wire must be connected to the terminal marked with the letter ‘E’ or the earth symbol
or
coloured green or green and yellow.
2.
The
BLUE wire must be connected to the terminal marked ‘N’ or coloured black.
3.
The
BROWN wire must be connected to the terminal marked ‘L’ or coloured red.
WELCOME
WARNINGS AND PRECAUTIONS
3
1
2
Connect input equipment as shown on page 4.
Plug the monitor into a mains socket and switch ON.
To switch ON press the power On / Off button on the front of the monitor. If the power to this monitor is interrupted whilst
it is switched on, when power is returned the monitor will automatically switch back on. To switch OFF press the power
On / Off button again.
1
2
Mains Power
On/Off switch
F
F
Selects a function from :
Volume, Contrast, Brightness,
Colour, Sharpness, Tint (M.NTSC
/ NTSC only), Aspect, Colour
Balance or Colour System
--- ,
+
When a function is already
displayed, allows adjustment
of the function.
When no function is displayed,
allows selection of AV source
from: Source A, Source B and
S---VHS Source B/S
Cursor Bar
Sound and picture adjustments are carried out using a series of On Screen Displays, accessed by pressing the
F key on the front
of the monitor.
Press
F repeatedly to select the required function.
The following adjustments may be made in turn: Volume, Contrast, Brightness, Colour, Sharpness,
Tint (M.NTSC / NTSC only), Aspect, Colour Balance or Colour System.
Press
(+) to increase or (---) to decrease the setting.
If the
F key is not pressed within a few seconds of each selection the display will disappear.
When the
F key on the front of the monitor is pressed again, the display will start off at Volume.
Colour System allows choice from: AUTO, PAL, SECAM, M.NTSC, NTSC.
FUNCTION SEQUENCE
Colour Balance
Contrast
Colour System
Brightness
Volume
Volume
Colour
Sharpness
Aspect
Tint (M.NTSC / NTSC only)
On Screen Displays
Front Panel Controls
Using the On Screen Displays (OSDs)
INSTALLATION AND SET---UP
LOCATION OF CONTROLS
ACCESSORIES
AC Mains Power Lead
(TSX8E0041)
4
Do not connect a computer with TTL output (5V) to this monitor.
Use 75W coaxial cable [RG---59/U (3C---2V), RG---6/U (5C---2V), RG---14/U (7C---2V), RG---15/U (10C---2V)].
Use 75W coaxial cable [RG---59/U (3C---2V), RG---6/U (5C---2V), RG---14/U (7C---2V), RG---15/U (10C---2V)].
This monitor is not classed as professional standard equipment. We recommend a MAXIMUM of 10 pieces when configured in a loop
system utilising the video out facility. Brightness adjustment may also be necessary to achieve desired performance. Total cable length
should not exceed 150m.
Connectors and cables shown are not supplied.
system utilising the video out facility. Brightness adjustment may also be necessary to achieve desired performance. Total cable length
should not exceed 150m.
Connectors and cables shown are not supplied.
Rear RCA Audio In / Out and BNC Video In / Out sockets
BNC
Video
cables
Rear AV sockets
BNC
Video
IN
RCA
Audio
cables
BNC
Video
OUT
BNC
Video
IN
RCA
Audio
IN
RCA
Audio
OUT
RCA
Audio
IN
S---Video
IN
S---Video
cable
AV Source A
IN / OUT
External equipment can be connected to the various AV inputs and outputs provided.
AV Source B/S
IN
AV Source B
IN
Select AV source via front panel
controls. See page 3.
Note:
Sources B and B/S use
the same RCA Audio IN socket.
Ensure the correct source
cable is connected.
Type of coaxial cable
RG---59/U(3C---2V)
RG---6U(5C---2V)
RG---11/U(7C---2V)
RG---15/U(10C---2V)
Recommended maximum
(ft)
825
1,650
1,980
2,640
Recommended maximum
cable length
(m)
250
500
600
800
Model Number
TC---M21K
TC---M14K
Power Source
220 -- 240V 50Hz A.C.
Power Consumption
48W
34W
Picture Tube
(visible diagonal)
51cm
34cm
Audio Output (Music)
6W, 8W impedance, Mono
Dimensions (HxWxD)
466x500x470
351x370x371
Weight
27kg
13kg
Colour System
PAL, SECAM, M.NTSC, NTSC, PAL60
AV --- Rear
A -- RCA Audio in/out, BNC Video in/out
B -- RCA Audio in, BNC Video in,
B/S -- 4 pin S--Video in, (RCA Audio in)
Video loop -- 10 pieces maximum
Design and specifications are subject to change without notice. Weights and dimensions shown are approximate.
00X
CONNECTION TO OTHER EQUIPMENT
SPECIFICATIONS
TROUBLESHOOTING
Interference
Electrical appliances,
cars / motorcycles,
fluorescent lights.
Symptom
Check
No picture, no sound
No colour
Normal picture, no sound
Not plugged into A.C. outlet.
Not switched on.
Picture/sound controls set to
minimum.
Check colour level.
Check volume level.