Read Panasonic TC-21PM30R / TX-28CK1 / TX-25CK1 / TX-21JT1C / TX-21JT1V / TX-14JT1C / TX-14JT1V / TX-21JT1C / TX-14JT1C / TC-21JR1C / TC-14JR1C / TX-21JT1 / TX-14JT1 / TC-14JT1 / TX-21CK1L / TX-21CK1B Service Manual online
Adjustment Procedure
Item / Preparation
Adjustment Procedure
+B Voltage
1. Operate the TV set.
Confirm the DC voltage at the indicated test points,
as follow :
as follow :
2. Set control as follow :
TPA 12 : 141.2 +- 0.8V
TPA 21 : 215 +- 15V
Brightness ..... minimum
TPA 11 : 8 +- 1V
Contrast ........ minimum
TPA 10 : 5 +- 1V
RF AGC
1. Receive a colour bar signal at an
1. Select “RF AGC” indication in CHK 2, on Screen
RF level of 64(+0-1)dBU with 75
by remote control at factory mode.
loaded.
2. Connect digital multimeter to RF AGC
2. Connect digital multimeter to RF AGC
2. Set RF AGC by using remote control volume (+)
at Tuner.
or volume (-) button until voltage AGC at Tuner
reach 2.7 +- 0.1V.
3. Increase RF signal strenght by 2dB, confirm
AGC at Tuner voltage drop.
reach 2.7 +- 0.1V.
3. Increase RF signal strenght by 2dB, confirm
AGC at Tuner voltage drop.
High Voltage
1. Receive the crosshatch pattern.
1. Connect a DC voltage meter to TPA 12
and confirm the +B voltage is 141.2 +- 0.8V.
and confirm the +B voltage is 141.2 +- 0.8V.
2. Set to 0 Beam .
2. Connect a high frequency voltmeter to heater and
Screen VR ..... minimum
confirm that voltage reads 6.3+- 0.24 (VRMS).
Contrast ....... minimum
3. Normalize the brightness and contrast.
Item / Preparation
Adjustment Produre
Connect oscilloscope probe to TPA32
(R-OUT) with 10Kohm series resistor.
Connect a short jumper between TPA 10
(R-OUT) with 10Kohm series resistor.
Connect a short jumper between TPA 10
1. Adjust Sub-Tint so that No.2,3 and 4 becomes
and TPA 20.
level waveform is similiar to Fig. 10.
Press Main Menu and Set system to
2. Confirm phase at Tint is changes more than
Use AV-NTSC (3.58MHz).
+/- 30 by Tint control.
DYNAMIC ....... Normal
3. Confirm that colour level is maximum when
colour DAC is adjusted to maximum position.
colour DAC is adjusted to maximum position.
Note:Use Remote control only when adjusting user mode
to Sub-Tint.
0.5a
a
7 8 9 10
1 2 3 4 5 6
Fig. 10
Ω
Click on the first or last page to see other TC-21PM30R / TX-28CK1 / TX-25CK1 / TX-21JT1C / TX-21JT1V / TX-14JT1C / TX-14JT1V / TX-21JT1C / TX-14JT1C / TC-21JR1C / TC-14JR1C / TX-21JT1 / TX-14JT1 / TC-14JT1 / TX-21CK1L / TX-21CK1B service manuals if exist.