TC-21D2Q - Panasonic TV Service Manual (repair manual)

tc-21d2q service manual
Model
TC-21D2Q
Pages
23
Size
4.49 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / MX-5Z
File
tc-21d2q.pdf
Date

Read Panasonic TC-21D2Q Service Manual online

Power Source :
AC AUTO 110-240V, 50/60 Hz
Power Consumption :
87W
Aerial Impedance :
75
unbalanced
Coaxial type
Receiving System :
17 Systems
Receiving Channels :
VHF
1-11 PAL B (Australia & N.Zealand)
1-12 PAL/SECAM D
1-12 NTSC M JAPAN
2-12 PAL/SECAM B, G
2-13 NTSC M U.S.A.
UHF
21-69 PAL G I/SECAM B, G, K1
28-69 PAL G (Australia)
13-56 PAL D
13-52 NTSC M JAPAN
14-69 NTSC NTSC M U.S.A.
CATV
S1-S41 (Hyper)
Intermediate Frequency :
Video
38.0 MHz
Sound
31.5 MHz (D, K, K1)
32 MHz (I)
32.5 MHz (B, G)
33.5 MHz (M)
Colour
33.57 MHz (PAL)
33.6 MHz (SECAM)
33.75 MHz (SECAM)
34.42 MHz (NTSC)
TC-21D2Q
MX-5Z Chassis
Video / Audio Terminals :
RAV In
Video In 1 Vp-p 75
Audio In Approx. 400mVrms
Monitor Out
Video Out 1 Vp-p 75
Audio Out Approx. 400mVrms
High Voltage :
28.0kV (±1.0)
at zero beam current
Picture Tube :
A51JXS064X
54cm (21 inches)
Measured diagony,
90° deflection
Audio Output :
3.0W
Speaker :
13 x 15cm, 16
Dimensions :
Height : 477.0 mm
Speaker :
Width : 518.0 mm
Depth : 477.0 mm
Mass :
20.4 kg (Net Wt.)
Note :
Specifications are subject to change without notice.
Mass and dimensions shown are approximate.
Colour Television
Specifications
ORDER NO. MTV0206168C3
 1 Safety Precautions 
3
 2 Service Hints 
5
 3 Conductor Views (TNP4G198AK) 
11
 4 Schematic Diagram 
13
 5 Parts Location 
17
 6 Replacement Parts List 
18
CONTENTS
 Page 
Page
2
TC-21D2Q
1 Safety Precautions
1.1. General Guide Lines
 1. It is advisable to insert an isolation transformer in the AC supply before servicing this hot chassis.
 2. When servicing, observe the original lead dress, especially the lead dress in the high voltage circuits. If a short circuit is found,
replace all parts which have been overheated or damaged by the short circuit.
 3. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers, shields and isolation R-C
combinations, are properly installed.
 4. When the receiver is not to be used for a long period of time, unplug the power cord from the AC cord outlet.
 5. Potential, as high as 27.0kV is present when this receiver is in operation. Operation of the receiver without the rear cover
involves the danger of a shock hazard from the receiver power supply. Servicing should not be attempted by anyone who is not
thoroughly familiar with the precautions necessary when working on high voltage equipment. Always discharge the anode of the
picture tube to the receiver chassis before handling the tube. After servicing make the following leakage current checks to
prevent the customer from being exposed to shock hazards.
1.2. Leakage Current Cold Check
 1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
 2. Turn on the receiver’s power switch.
Measure the resistance value, with an ohmmeter, between the jumper AC plug and each exposed metallic cabinet part on the
receiver, such as screw heads, aerials, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 4 M
and 20 M
. When the exposed metal does not have a return path to the chassis,
the reading must be infinite.
1.3. Leakage Current Hot Check (Fig. 1)
 1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
 2. Check a 2 k
non-inductive resistor and an AC/DC current meter, in series with each exposed metallic part on the receiver in
turn and an earth such as a water pipe.
The current from any point should not exceed 0.7 mA peak AC or 2 mA DC. In the case of a measurement being outside of
these limits specified, there is a possibility of a shock hazard and the receiver should be repaired and rechecked before it is
returned to the customer.
Fig. 1
,
1.4. X-Radiation
Warning:
The potential sources of X-Radiation in TV set are the EHT section and the picture tube. When using a picture tube test jig for
service, ensure that jig is capable of handling 29.0kV without causing X-Radiation.
Note : It is important to use an accurate periodically calibrated high voltage meter.
 1. Set the brightness to minimum.
 2. Use the remocon to get into Service Mode.
 3. Measure the EHT. The meter reading should indicate 28.0±1.0kV. If the meter indication is out of tolerance, immediate service
and correction is required to prevent the possibility of premature component failure.
 4. To prevent the possibility X-Radiation, it is essential to use the specified picture tube, if service replacement becomes
necessary.
3
TC-21D2Q
1.5. MX-5Z Chassis Block Diagram
4
TC-21D2Q
Page of 23
Display

Download Panasonic TC-21D2Q Service Manual (Repair Manual)

Here you can read online and download Panasonic TC-21D2Q Service Manual in PDF. TC-21D2Q service manual will guide through the process and help you recover, restore, fix, disassemble and repair Panasonic TC-21D2Q TV. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.