TC-15PM10R, TC-14D3, TC-21D3, TX-14D3T, TX-21D3T - Panasonic TV Service Manual (repair manual)

tc-15pm10r, tc-14d3, tc-21d3, tx-14d3t, tx-21d3t service manual
Model
TC-15PM10R TC-14D3 TC-21D3 TX-14D3T TX-21D3T
Pages
26
Size
3.44 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / MX-7
File
tc-15pm10r-tc-14d3-tc-21d3-tx-14d3t-tx-21d3t.pdf
Date

Read Panasonic TC-15PM10R / TC-14D3 / TC-21D3 / TX-14D3T / TX-21D3T Service Manual online

Power Source :
AC AUTO 110-240V, 50/60Hz
Power Consumption :
69W
Aerial Impedance:
75
unbalanced Coaxial type
Receiving System :
17 System
Receiving Channels :
VHF
2-12 (PAL/SECAM B,K1) 0-12
(PAL B AUST)1-9 (PAL B N.Z) 1-
12 (PAL/SECAM D) 1-12 (NTSC M
JAPAN) 2-13 (NTSC M U.S.A)
UHF
21-69 (PAL G,H,I/SECAM
G,K,K1)28-69 (PAL B AUST) 13-
57 (PAL D,K)13-62 (NTSC M
JAPAN)14-69 (NTSC M U.S.A)
CATV
S1-S41(OSCAR) 1-125 (U.S.A
CATV) C13-C41(JAPAN) S21-S41
(HYPER)Z1-Z37 (CHINA)
Intermediate Frequency :
Video
38.0 MHz
Sound
31.5 MHz (D,K) / 32.5MHz (B,G)
32.0 MHz (I) / 32.5MHz (M)
TC-15PM10R
MX-7 Chassis
Colour
33.57
MHz
(PAL)33.6
MHz
(SECAM)
32.5 MHz (B,G)33.75
MHz (SECAM) 34.42 MHz (NTSC)
Video / Audio Terminals :
FAV In :
Video In 1 Vp-p 75
Video In
Approx, 400mVrms
Monitor Out :
Video Out1 Vp-p 75
Audio
OutApprox, 400mVrms
RAV In :
Video In 1 Vp-p 75
Audio in:
Approx. 400m Vrms
High Voltage :
27.5 kV ( ± 1.0 )at zero beam
current
Picture Tube :
A36LTN194x36cm (15
inches)Measured diagony, 90°
deflection
Audio Output :
3.5W
Dimensions :
Height : 373.5 mmWidth : 385.0
mmDepth : 379.8 mm
Mass :
12.5 kg
Specifications
are
subject
to
change
withoutnotice.Mass
dimensions shown are approximate.
Colour Television
Specification
ORDER NO. MTV 0006136C3
 1 
Safety Precautions 
2
 1.1. 
General Guide Lines 
2
 1.2. 
Leakage Current Cold Check 
2
 1.3. 
Leakage Current Hot Check (Fig. 1) 
2
 1.4. 
X-Radiation 
3
 1.5. 
MX-7 Chassis Block Diagram 
3
 2 
Service Hints 
4
 2.1. 
Service Position for E-Board 
4
 2.2. 
Factory mode adjustment 
4
 2.3. 
Adjustment for White Balance 
4
 2.4. 
Adjustment for CRT CUT OFF 
4
 2.5. 
Adjustment Procedure 
5
 2.6. 
Pal Colour 
5
 2.7. 
Adjustment 
6
 3 
L-BOARDTNP4G137AU(S’PORE)TNP4G137AD(M’EAST/CIS) 9
 4 
Z1-BOARDTNP4G139AA 
10
 5 
A-BOARDTNP4G136AD(M’EAST)TNP4G136AU(S’PORE) 
11
 6 
Schematic Diagram for models TC-15PM10R (MX-7 Chassis)
 
13
 7 
CRT 
14
 8 
Speakers 
15
 9 
Schematic Diagram 
17
 10 Replacement Parts List 
19
CONTENTS
 Page 
Page
1 Safety Precautions
1.1. General Guide Lines
 1. It is advisable to insert an isolation transformer in the AC supply before servicing this hot chassis.
 2. When servicing, observe the original lead dress, especially the lead dress in the high voltage circuits. If a short circuit is found,
replace all parts which have been overheated or damaged by the short circuit.
 3. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers, shields, and isolation R-C
combinations, are properly installed.
 4. When the receiver is not to be used for a long period of time, unplug the power cord from the AC cord outlet.
 5. Potential, as high as 28.5kV. is present when this receiver is in operation. Operation of the receiver without the rear cover
involves the danger of a shock hazard from the receiver power supply. Servicing should not be attempted by anyone who is not
thoroughly familiar with the precautions necessary when working on high voltage equipment. Always discharge the anode of the
picture tube to the receiver chassis before handling the tube. After servicing make the following leakage current checks to
prevent the customer from being exposed to shock hazards.
1.2. Leakage Current Cold Check
 1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
 2. Turn on the receiver’s power switch.
Measure the resistance value, with an ohmmeter, between the jumper AC plug and each exposed metallic cabinet part on the
receiver, such as screw heads, aerials, connectors, control shafts, ect. When the exposed metallic part has a return path to the
chassis, the reading should be between 4 Mohm and 20 M
.When the exposed metal does not have a return path to the
chassis, the reading must be infinite.
1.3. Leakage Current Hot Check (Fig. 1)
 1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
 2. Check a 2 k
non-inductive resistor and an AC/DC current meter, in series with each exposed metallic part on the receiver in
turn and an earth such as a water pipe. The current from any point should not exceed 0.7 mA peak AC or 2 mA DC. In the case
of a measurement being outside of these limits specified, there is a possibility of a shock hazard, and the receiver should be
repaired and rechecked before it is returned to the customer.
2
TC-15PM10R
Fig. 1
1.4. X-Radiation
Warning :
The potential sources of X-Radiation in TV set are the EHT section and the picture tube. When using a picture tube test jig for
service, ensure that jig is capable of handling 28.5kV without causing X-Radiation. Note: It is important to use an accurate
periodically calibrated high voltage meter.
 1. Set the brightness to minimum.
 2. Use the remocon to get into Service Mode.
 3. Measure the EHT. The meter reading should indicate 27.5(+-1.0)kV. If the meter indication is out of tolerance, immediate
service and correction is required to prevent the possibility of premature component failure.
 4. To prevent the possibility X-Radiation, it is essential to use the specifield picture tube, if service replacement becomes
necessary.
1.5. MX-7 Chassis Block Diagram
TUNER
SA
AUDIO
EAR 
PHONE
SPEAER
 OUT
D
H OUT
FBT
SCREEN
FOCUS
RGB
IC601
EHT
CRT
TONE
E
CIRCUIT
SIF
TRAP
POE
R
SA
FM  DEMOD.
 ( Z - BOARD ).
3
TC-15PM10R
2 Service Hints
2.1. Service Position for E-Board
 1. Remove the back cover.
 2. Stand the TV set as shown in fig. 7
 3. Remove the A-Board from the TV set by pulling the main board out as shown in figure 7.
Fig. 7
2.2. Factory mode adjustment
How to set:
To set the Factory mode, press Volume 0 dac on the TV and TImer Setting 30 Min on
the remote control and press Volume (-) Down button on the TV together press recall on
the remote control.
To Set Self-Check:
Press the volume down button on TV then press the off timer button on remote control.
2.3. Adjustment for White Balance
Preparation:
 1. Receive the white balance pattern and aging should have been performed over 30 minutes.
 2. Set the picture menu to DYNAMIC NORMAL.
 3. Degause the CRT face.
 4. Fix the CRT colour analyzer receiver unit to CRT face.
Adjustment of Low Light.
 1. Adjustment Sub Bright, so that Y = 6.3 ± 1.0 unit
 2. Adjustment R-CUT OFF, so that Y = 0.235 ± 0.01 unit
 3. Adjustment G-CUT OFF, so that Y = 0.235 ± 0.01 unit
Adjustment of High Light
 1. Adjustment Sub Bright, so that Y = 390 unit
 2. Adjustment R-Drive, so that Y = 0.259 ± 0.01 unit
 3. Adjustment B-Drive, so that Y = 0.259 ± 0.01 unit
2.4. Adjustment for CRT CUT OFF
Preparation:
 1. Connect the oscilloscope probe to TPL7.
 2. Screen VR min.
4
TC-15PM10R
Page of 26
Display

Download Panasonic TC-15PM10R / TC-14D3 / TC-21D3 / TX-14D3T / TX-21D3T Service Manual (Repair Manual)

Here you can read online and download Panasonic TC-15PM10R / TC-14D3 / TC-21D3 / TX-14D3T / TX-21D3T Service Manual in PDF. TC-15PM10R / TC-14D3 / TC-21D3 / TX-14D3T / TX-21D3T service manual will guide through the process and help you recover, restore, fix, disassemble and repair Panasonic TC-15PM10R / TC-14D3 / TC-21D3 / TX-14D3T / TX-21D3T TV. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.