Read Panasonic KX-TG7175RUS / KX-TGA717RUS Service Manual online
25
KX-TG7175RUS/KX-TGA717RUS
8.2.
EEPROM LAYOUT (Base Unit)
8.2.1.
Scope
The purpose of this section is to describe the layout of the EEPROM (IC5) for the KX-TG7175 base unit.
The EEPROM contains hardware, software, and user specific parameters. Some parameters are set during production of the
base unit, some are set by the user configuration, and some are set during normal use of the phone.
base unit, some are set by the user configuration, and some are set during normal use of the phone.
8.2.2.
Introduction
The base unit uses a 128k bit serial EEPROM (IC5) for storing volatile parameters. All parameters are set up before the base
unit leaves the factory. Some of these are vital for the operation of the hardware so a set of default parameters is programmed
before the actual hardware fine-tuning can be initiated. This document lists all default settings with a short description.
unit leaves the factory. Some of these are vital for the operation of the hardware so a set of default parameters is programmed
before the actual hardware fine-tuning can be initiated. This document lists all default settings with a short description.
8.2.3.
EEPROM Layout
General Setup1:
General Setup2:
Initial Type
Description
F
The data initialized by only F command
0
The data initialized by F and 0 command
1
The data initialized by F, 0 and 1 command
2
The data initialized by F, 0, 1 and 2 command
3
The data initialized by all command (F, 0, 1, 2, 3)
Country Setting
Description
x
Default - no specific country setting, so revert to default value.
Address
Initial
Type
Name
Description
Default value
Country
Setting
0000
-
EEP_EepromType
EEPROM type
0x00:32kbit type
0x55:64kbit type
0xAA:128kbit type
other:32kbit type
0x00:32kbit type
0x55:64kbit type
0xAA:128kbit type
other:32kbit type
0x00
x
0007
F
EEP_ModelInfo
Model information
Bit0:TAM...1:Enable, 0:Disable
Bit1:Base Phonebook 1...1:Enable, 0:Disable
Bit2:Audible Call...1:Enable, 0:Disable
Bit3:SP-PHONE...1:Enable, 0:Disable
Bit4:FAX...1:Enable, 0:Disable
Bit5:TalkOver...1:Enable, 0:Disable
Bit6-7:Not used
Bit0:TAM...1:Enable, 0:Disable
Bit1:Base Phonebook 1...1:Enable, 0:Disable
Bit2:Audible Call...1:Enable, 0:Disable
Bit3:SP-PHONE...1:Enable, 0:Disable
Bit4:FAX...1:Enable, 0:Disable
Bit5:TalkOver...1:Enable, 0:Disable
Bit6-7:Not used
0x00
x
031D
1
EEP_MenusEnabled2
Menus Enabled2
Bit0-2=Menu of Select Base Rest Mode
0:Default, 1:Germany or Austria, 2-:Reserve
Bit3-7=(Reserve)
Bit0-2=Menu of Select Base Rest Mode
0:Default, 1:Germany or Austria, 2-:Reserve
Bit3-7=(Reserve)
0x00
x
Address
Initial
Type
Name
Description
Default value
Country
Setting
0001
F EEP_FreqTrim_L
Setting value of FREQ_TRIM_REG
0x75
x
0002
F
EEP_BandGap
Setting value of BandGap REG
0x08
x
0010
-
EEP_Rfpi
Base ID
written data by adjustment checker or ID writer
RFPI (5Byte)
written data by adjustment checker or ID writer
RFPI (5Byte)
0xFF,0xFF,0xFF,0xFF,
0xFF
x
0300
1
EEP_Rc0
BMC internal Register 0
0x40
x
0022
0
EEP_Ps0_InUseFlag
IN-Use Flag
00:Invalid / 01:Valid
00:Invalid / 01:Valid
0x00
x
0023
0
EEP_Ps0_DectPsNo
DECT PS No.
00-3F:PS No. / FF:Invalid
00-3F:PS No. / FF:Invalid
0xFF
x
0024
0
EEP_Ps0_PsType
PS Type
00:KME's PS (Group Page)
01:KME's PS (Group Page/Message Waiting)
02:TD-7500 or TD-7590 / FF:Another Maker's PS
00:KME's PS (Group Page)
01:KME's PS (Group Page/Message Waiting)
02:TD-7500 or TD-7590 / FF:Another Maker's PS
0xFF
x
Click on the first or last page to see other KX-TG7175RUS / KX-TGA717RUS service manuals if exist.