Read Panasonic KX-TG7107UAS / KX-TG7107UAT / KX-TG7108UAS / KX-TG7108UAT / KX-TGA710UAS / KX-TGA710UAT Service Manual online
61
KX-TG7107UAS/KX-TG7107UAT/KX-TG7108UAS/KX-TG7108UAT/KX-TGA710UAS/KX-TGA710UAT
11.6. Things to Do after Replacing IC
Cautions:
Some of the content on this page may not apply to models from some countries. The contents below are the minimum adjust-
ments required for operation.
ments required for operation.
11.6.1. Base Unit
Before making the following adjustment, ensure you have carried out PC Setting (P.54) in The Setting Method of JIG (Base
Unit).
Unit).
Note:
(*1) XX: country code, YY: revision number
“XX” and “YY” vary depending on the country version. You can find them in the batch file, PQZZ- mentioned in JIG and PC
(P.54).
(*2) Refer to Check Point (Base Unit) (P.41)
“XX” and “YY” vary depending on the country version. You can find them in the batch file, PQZZ- mentioned in JIG and PC
(P.54).
(*2) Refer to Check Point (Base Unit) (P.41)
11.6.2. Handset
Before making the following adjustment, ensure you have carried out Batch file Settings (P.55) in The Setting Method of JIG
(Handset).
(Handset).
Note:
(*3) XX: country code, YY: revision number
“XX” and “YY” vary depending on the country version. You can find them in the batch file, PQZZ- mentioned in JIG and PC
(P.54).
(*4) Refer to Check Point (Handset) (P.45)
“XX” and “YY” vary depending on the country version. You can find them in the batch file, PQZZ- mentioned in JIG and PC
(P.54).
(*4) Refer to Check Point (Handset) (P.45)
IC
Necessary Adjustment
BBIC
(IC7)
(IC7)
Programs for Voice processing, interface for RF and
EEPROM
EEPROM
1. Default batch file: Execute the command “default.bat”.
2. Country version batch file: Execute the command
2. Country version batch file: Execute the command
“TG7100XXrevYY.bat”. (*1)
3. Clock adjustment: Refer to Check Point (F). (*2)
EEPROM
(IC5)
(IC5)
Adjustment parameter data
(country version batch file, default batch file, etc.)
(country version batch file, default batch file, etc.)
1. Change the address “0000” of EEPROM to “00”.
2. Default batch file: Execute the command “default.bat”.
3. Country version batch file: Execute the command
2. Default batch file: Execute the command “default.bat”.
3. Country version batch file: Execute the command
“TG7100XXrevYY.bat”. (*1)
4. Clock adjustment: Refer to Check Point (F). (*2)
IC
Necessary Adjustment
BBIC
(IC1)
(IC1)
Programs for Voice processing, interface for RF and
EEPROM
EEPROM
1. Default batch file: Execute the command “default.bat”.
2. Default batch file (remaining); Execute the command
2. Default batch file (remaining); Execute the command
“TGA710 DEFrevYY.bat”. (*3)
3. Country version batch file: Execute the command
“TGA710XXrevYY”. (*3)
4. Clock adjustment: Refer to Check Point (J). (*4)
5. 1.8 V setting and battery low detection: Refer to Check
5. 1.8 V setting and battery low detection: Refer to Check
Point (A), (H) and (I). (*4)
EEPROM
(IC3)
(IC3)
Adjustment parameter data
(country version batch file, default batch file, etc.)
(country version batch file, default batch file, etc.)
1. Change the address “0015” of EEPROM to “00”.
2. Default batch file: Execute the command “default.bat”.
3. Default batch file (remaining); Execute the command
2. Default batch file: Execute the command “default.bat”.
3. Default batch file (remaining); Execute the command
“TGA710 DEFrevYY.bat”. (*3)
4. Country version batch file: Execute the command
“TGA710XXrevYY”. (*3)
5. Clock adjustment: Refer to Check Point (J). (*4)
6. 1.8 V setting and battery low detection: Refer to Check
6. 1.8 V setting and battery low detection: Refer to Check
Point (A), (H) and (I). (*4)
Click on the first or last page to see other KX-TG7107UAS / KX-TG7107UAT / KX-TG7108UAS / KX-TG7108UAT / KX-TGA710UAS / KX-TGA710UAT service manuals if exist.