Read Panasonic KX-TG1401UAH / KX-TG1401UAL / KX-TG1402UA3 / KX-TG1411UAM / KX-TG1411UAT / KX-TG1412UA1 / KX-TGA131RUH / KX-TGA131RUL / KX-TGA131RUM / KX-TGA131RUT Service Manual online
28
KX-TG1401UA/KX-TG1402UA/KX-TG1411UA/KX-TG1412UA/KX-TGA131RU
(G) Battery Low
Confirmation (Important)
-
1. Apply 2.40V between BATTERY (+) and BATTERY (-).
2. Confirm that there is no Speaker sound (Battery low alarm).
3. Apply 2.1V between BATTERY(+) and BATTERY(-).
4. Confirm that there is Speaker sound (Battery low alarm).
2. Confirm that there is no Speaker sound (Battery low alarm).
3. Apply 2.1V between BATTERY(+) and BATTERY(-).
4. Confirm that there is Speaker sound (Battery low alarm).
Career
module,D107,
C109, C125,
R117, R116,
C125, R117,
R116, Q104,
Q105, D104,
R115,
BUZZER
module,D107,
C109, C125,
R117, R116,
C125, R117,
R116, Q104,
Q105, D104,
R115,
BUZZER
(H)* BBIC Clock Adjustment
(Important)
P1.0
CLK
CLK
1. Apply 2.6V between BATTERY (+) and BATTERY (-) with DC power.
2. Execute the command “EnableClockOutput”.
3. Input Command “rdeeprom 00 00 02", then you can confirm the current value.
4. Check X’tal Frequency. (10.368 MHz ± 100 Hz).
5. If the frequency is not 10.368 MHz ± 100 Hz, adjust the frequency of CLK
2. Execute the command “EnableClockOutput”.
3. Input Command “rdeeprom 00 00 02", then you can confirm the current value.
4. Check X’tal Frequency. (10.368 MHz ± 100 Hz).
5. If the frequency is not 10.368 MHz ± 100 Hz, adjust the frequency of CLK
executing the command “setfreq sfr xx xx (where xx is the value)” so that the
reading of the frequency counter is 10.368000 MHz ± 5 Hz.
Note:
Clear the registered information for Base Unit before measurement, because
the Frequency will not possibly get stable due to the registered information.
Pressing the button of “3” “7” “9” “#” clears the registration. Register to it on
Base Unit after measurement.
reading of the frequency counter is 10.368000 MHz ± 5 Hz.
Note:
Clear the registered information for Base Unit before measurement, because
the Frequency will not possibly get stable due to the registered information.
Pressing the button of “3” “7” “9” “#” clears the registration. Register to it on
Base Unit after measurement.
C127, C122,
C123, X101
C123, X101
(I)* Transmitted Power
Confirmation
ANT
Remove the Antenna before starting steps from 1 to 5.
1. Configure the DECT tester (CMD60) as follows;
<Setting>
• Test mode: PP
• RFPI: 0102030405
• Traffic Channel: 5
• Traffic Slot: 4
• Mode: Loopback
• RFPI: 0102030405
• Traffic Channel: 5
• Traffic Slot: 4
• Mode: Loopback
2. Execute the command “regcmd60”.
3. Initiate connection from DECT tester.
4. Confirm that the NTP value at ANT is -19dBm ~ 25dBm.
3. Initiate connection from DECT tester.
4. Confirm that the NTP value at ANT is -19dBm ~ 25dBm.
Career
module, R1,
R2, C21, C23,
L3, L4, C15,
C20, D2, C17
module, R1,
R2, C21, C23,
L3, L4, C15,
C20, D2, C17
(J)* Modulation Check
ANT
Follow steps 1 to 4 of (I).
4. Confirm that the B-Field Modulation is 340kHz/div ~ 402kHz/div using data
type Fig31.
type Fig31.
Career
module, R1,
R2, C21, C23,
L3, L4, C15,
C20, D2, C17
module, R1,
R2, C21, C23,
L3, L4, C15,
C20, D2, C17
(K)* Frequency Offset
Confirmation
-
Follow steps 1 to 4 of (I).
4. Confirm that the frequency offset is -50kHz ~ +50kHz.
Career
module, R1,
R2, C21, C23,
L3, L4, C15,
C20, D2, C17
module, R1,
R2, C21, C23,
L3, L4, C15,
C20, D2, C17
(L)* Sensitivity Receiver
Confirmation
-
Follow steps 1 to 4 of (I).
4. Set DECT tester power to -85dBm.
5. Confirm that the BER is < 1000ppm.
5. Confirm that the BER is < 1000ppm.
R1, R2, C21,
C23, C1, C8,
C7, C12, C13,
L1, L2, C18,
C19, D1, C17
C23, C1, C8,
C7, C12, C13,
L1, L2, C18,
C19, D1, C17
(M)* Timing Confirmation
-
Follow steps 1 to 4 of (I).
4. Confirm that the Timing accuracy is < ± 2.0ppm.
R1, R2, C21,
C23, C1, C8,
C7, C12, C13,
L1, L2, C18,
C19, D1, C17
C23, C1, C8,
C7, C12, C13,
L1, L2, C18,
C19, D1, C17
(N)* RSSI Level Confirmation -
Follow steps 1 to 4 of (I).
4. Set DECT tester power to -70dBm.
5. Execute the command “readrssi”.
6. Confirm: 9 < returned value < 13 (hex) (0E ± 5 (hex))
5. Execute the command “readrssi”.
6. Confirm: 9 < returned value < 13 (hex) (0E ± 5 (hex))
R1, R2, C21,
C23, C1, C8,
C7, C12, C13,
L1, L2, C18,
C19, D1, C17
C23, C1, C8,
C7, C12, C13,
L1, L2, C18,
C19, D1, C17
(O) Audio Check and
Confirmation
-
1. Link to BASE which is connected to Line Simulator.
2. Set line voltage to 48V and line current to 40mA.
3. Input -45dBm/1KHz to MIC and measure Line output level.
4. Confirm that the level is -9.5 ± 3dBm and that the distortion level is < 5% at TEL
2. Set line voltage to 48V and line current to 40mA.
3. Input -45dBm/1KHz to MIC and measure Line output level.
4. Confirm that the level is -9.5 ± 3dBm and that the distortion level is < 5% at TEL
Line (600
Ω Load).
5. Input -20dBm/1KHz to Line I/F and measure Receiving level at SP+ and SP-.
6. Confirm that the level is -21.5 ± 3dBm and that the distortion level is < 5% at
6. Confirm that the level is -21.5 ± 3dBm and that the distortion level is < 5% at
Receiver. (vol = middle, 150
Ω Load)
Items
Adjustment
Point
Procedure
Check or
Replace Parts
Click on the first or last page to see other KX-TG1401UAH / KX-TG1401UAL / KX-TG1402UA3 / KX-TG1411UAM / KX-TG1411UAT / KX-TG1412UA1 / KX-TGA131RUH / KX-TGA131RUL / KX-TGA131RUM / KX-TGA131RUT service manuals if exist.