KX-TCD700 - Panasonic Telephone Service Manual Supplement (repair manual)

kx-tcd700 service manual supplement
Model
KX-TCD700
Pages
13
Size
634.47 KB
Type
PDF
Document
Service Manual Supplement
Brand
Device
Telephone / DECT
File
kx-tcd700.pdf
Date

Read Panasonic KX-TCD700 Service Manual Supplement online

KX-TCD700SERIES
Digital Cordless Phone
Black Version
Grey Version
Blue Version
(for Germany,Greece,France,Italy,Spain,United
Kingdom,Holland,Russia,Turkey,Austria,
Poland,Belgium,Nordic
model,Switzerland,Hong
Kong,Asia,Portugal,Denmark,Czech,Hu
ngary)
Telephone Equipment
Please file and use this supplement manual together with the service manuals mentioned below.
ORDER NO. KM40110828S8
1 CHANGES
This supplement has been issued for changes of Handset P.C.Board. Newer versions of the handset have the EEPROM mask
etched into the BBIC. These “Masked” units can be identified by the absence of IC3 on the component side of the P.C. Board.
The position of IC3 is shown in the “Component View” section of the service manual (section 17.1 or 19.1).
The masked and non-masked P.C.Board parts are both listed in section 3. REPLACEMENT PARTS LIST. Note that the
LCD and P.C.Board are not available separately. This is because the equipment required for bonding the cable to the
P.C.Board is normally beyond the scope of a typical service centre.
Model No.
Order NO.
Sup. NO
Countries/Areas
KX-TCD700GB/KX-TCD700GH
KM40101759C2
1
Germany
KX-TCD700GRC/KX-TCD700GRH
KM40104794C2
1
Greece
KX-TCD700FRB/KX-TCD700FRH
KM40101579C2
1
France
KX-TCD700JTC
KM40105798C2
1
Italy
KX-TCD700SPC/KX-TCD700SPH
KM40105797C2
1
Spain
KX-TCD700EB
KM40104793C2
1
United Kingdom
KX-TCD700NLC
KM40106811C2
1
Holland
KX-TCD700RUB/KX-TCD700RUC
KM40107827C3
1
Russia
KX-TCD700TRB/KX-TCD700TRH
KM40107836C2
1
Turkey
KX-TCD700ARC
KM40109680C2
1
Austria
KX-TCD700PDB/KX-TCD700PDC
KM40109682C2
1
Poland
KX-TCD700BLB
KM40109681C2
1
Belgium
KX-TCD700NEB
KM40109683C2
1
Nordic
KX-TCD700SLC
KM40109684C2
1
Switzerland
KX-TCD700HKC
KM40109685C3
1
Hong Kong
KX-TCD700BXB/KX-TCD700BXC
KM40109686C3
1
Asia,Middle near East and Other areas
KX-TCD700PRB
KM40109687C2
1
Portugal
KX-TCD700DMB
KM40110697C2
1
Denmark
KX-TCD700HGB/KX-TCD700HGC
KM40110707C2
1
Hungary
KX-TCD700CXB/KX-TCD700CXC
KM40110708C3
1
Czech
2 CIRCUIT OPERATION (HANDSET)
(Changed from original section 6. CIRCUIT OPERATION (HANDSET))
BLOCK DIAGRAM BASEBAND SECTION (HANDSET)
2
KX-TCD700SERIES
2.1. THE BASE BAND SECTION
(Changed from original section 6.1. THE BASE BAND SECTION)
2.1.1. THE BASE-BAND INTEGRATED CIRCUIT (BBIC)
(Changed from original section 6.1.2. THE BASE-BAND INTEGRATED CIRCUIT (BBIC))
The PMB6720 (IC1) is a CMOS device designed to handle all the audio, signal and data processing needed in a DECT
handset. It contains a "burst mode controller" which takes care of DECT specific physical layer and radio section control.
It also contains an ADPCM codec filter used for speech encoding and decoding in the DSP section, a general purpose
microcontroller, various other ADC´s, DAC´s, timers and power control circuitry. It connects to the EEPROM (IC2) via a serial
interface (SDA and SDC). This serial interface is also used during manufacture and service to connect to an external computer.
The CPU contains 88k of ROM, so there is no need for any external memory provision.
(Original section 6.1.3. FLASH ROM has been deleted)
2.1.2. EEPROM (SEE Fig. 24)
(Changed from original section 6.1.4. EEPROM (SEE Fig. 24))
The electrically erasable PROM IC2 is used to store all the temporary operating parameters for the handset (see EEPROM
LAYOUT). It uses a two-line serial data interface with the BBIC, with bi-directional data on IC2 pin5 (TP52), and a 45 kHz
clock on pin 6 (TP53).
2.1.3. FACTORY SERIAL PORT (SEE Fig. 24)
(Changed from original section 6.1.5. FACTORY SERIAL PORT (SEE Fig. 24))
In order to communicate with the handset during manufacture and servicing (using a PC) a serial data link has been provided.
Serial data input/output is provided through the I2DAT input (pin 64). The data is clocked through using the I2CLK pin (65). Test
probe pads SDA and SDC are provided for Flash PROM download with I2DAT and I2CLK respectively.
To invoke the flash PROM download mode the MODE_SEL test pad must be connected to the 2.65V pad.
A Ground reference solder pad is also provided.
Fig.24
3
KX-TCD700SERIES
2.1.4. 
AUDIO PATH - TX AUDIO (SEE Fig. 25)
(Changed from original section 6.1.7. AUDIO PATH-TX AUDIO (SEE Fig. 25))
The audio signal from the microphone (TP23) enters the BBIC at pin 44. RF decoupling and signal conditioning are provided
by C17, R21, and C14.
In the BBIC the signal passes through the analogue section where it is amplified and converted to a digital audio stream signal.
The burst mode controller processes this stream performing encryption and scrambling, adding the various other fields to
produce the GAP standard DECT frame, assigning to a time slot and channel etc. to emerge on pin 14 as TXDA.
2.1.5. 
AUDIO PATH - RX AUDIO (SEE Fig. 25)
(Changed from original section 6.1.8. AUDIO PATH-RX AUDIO (SEE Fig. 25))
Audio from the receiver RXDA enters the BBIC on pin 10 as GAP standard DECT frames. It passes through the decoding
section burst mode controller where it separates out the frame information and performs de-encryption and de-scrambling as
required. It then goes to the DSP where it is turned back into analogue audio. This is amplified by the analogue front end and
emerges at pin 40 and 41. The telephone speaker is driven directly from the BBIC output ports.
On 700 models the ring alarm is provided by means of a buzzer BUZ1 which is switched by T4 from pin 68.
2.1.6. CLOCK GENERATION (SEE Fig. 25)
(Changed from original section 6.1.9. CLOCK GENERATION (SEE Fig. 25))
A single clock generator in the BBIC uses an external crystal X1 to derive all clock frequencies used in the handset. The crystal
is tuned to the exact frequency of 10.368 MHz during manufacture.
The BBIC provides a reference clock signal SYRI (pin 21, TP101) which is used to drive the PLL circuitry in the RF module. The
basic data rate for TXDA (pin 14) and RXDA (pin 10) is 1.152 Mbits/s, which is 10.368MHz divided by 9.
Fig.25
4
KX-TCD700SERIES
Page of 13
Display

Download Panasonic KX-TCD700 Service Manual Supplement

Here you can read online and download Panasonic KX-TCD700 Service Manual Supplement in PDF. KX-TCD700 service manual supplement will guide through the process and help you recover, restore, fix, disassemble and repair Panasonic KX-TCD700 Telephone. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.