PT-RZ770, PT-RW730, PT-RZ660, PT-RW620 (serv.man2) - Panasonic Projector Service Manual (repair manual). Page 3

Read Panasonic PT-RZ770 / PT-RW730 / PT-RZ660 / PT-RW620 (serv.man2) Service Manual online

3
PREFACE
< RZ770/RW730/RZ660/RW620 >
There are special components used in this equipment which are important for safety. These parts are marked by 7 in the schematic 
diagram, circuit board diagrams, exploded views and replacement parts list. It is essential that these critical parts should be replaced 
with manufacturer’s specified parts to prevent shock, fire, or other hazards. Do not modify the original design without permission of 
manufacturer.
IMPORTANT SAFETY NOTICE
WARNING:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
CAUTION:
Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device.
Cautions when transporting
f
 Move the lens position to the home position, remove the projection lens, and attach the lens hole cover when      
   transporting. 
   To move the lens to home position, perform the following procedure.
    1) Press the [DEFAULT] button on the remote control
        while the shift adjustment screen is displayed.
    2) Press qw to switch and select the used lens.
    3) Press the [ENTER] button.
f
 Hold the bottom of the projector and do not hold the projection lens or the opening around the projection lens
   when transporting. Failure to do so may cause damage. Also, handle the projector in a way not to apply 
   excessive vibration or shock. Failure to do so may cause a failure due to the damaged internal components.
f
 Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.
Cautions when installing
r
 After attaching the projection lens, be sure to attach the Lens Mount Cover.
Not doing so may cause failure due to accumulating dust internally.
r
 Do not set up the projector outdoors.
The projector is designed for indoor use only.
r
 Do not set up the projector in the following locations.
f
 Places where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal 
components or malfunction.
f
 Location close to sea or where corrosive gas may occur: The projector may fall due to corrosion. Also, failure to 
do so may shorten the life of the components and result in malfunction.
f
 Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare 
cases due to the heated air from the air exhaust port or the hot or cooled air from the air conditioner. Make sure 
that the exhaust from the projector or other equipment, or the air from the air conditioner does not blow toward 
the front of the projector.
 
f
Places with sharp temperature fluctuations such as near lights (studio lamps): Doing so may shorten the life of 
the light source, or result in deformation of the projector due to heat, which may cause malfunctions.
Follow the operating environment temperature of the projector.
 
f
Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.
 
f
Places where there is high-power laser equipment: Directing a laser beam onto the projection lens surface 
causes damage to the DLP chips.
Lens hole cover
Lens protection material
Page of 125
Display

Click on the first or last page to see other PT-RZ770 / PT-RW730 / PT-RZ660 / PT-RW620 (serv.man2) service manuals if exist.