Read Panasonic PT-RZ670 / PT-RW630 (serv.man18) Service Manual online
SECTION 1 SERVICE INFORMATION
< RZ670/RW630 >
1. 4. Remote control
1
3
2
4
5
7
6
8
9
10
15
12
11
13
14
14
16
17
Front
Top
Bottom
1 Power standby <
v> button
Sets the projector to the state where the projector is switched
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
2 Power on <
b> button
Starts projection when the <MAIN POWER> switch on the
projector is set to <ON> when the power is switched off
(standby mode).
projector is set to <ON> when the power is switched off
(standby mode).
3 Remote control indicator
Blinks if any button in the remote control is pressed.
4 Lens (<FOCUS>, <ZOOM>, <SHIFT>) buttons
Adjusts the projection lens.
5 <MENU> button/<ENTER> button/
asqw buttons
Used to navigate through the menu screen.
6 <ON SCREEN> button
Switches the on-screen display function on (display) or off
(hide).
(hide).
7 Input selection (<RGB1/2>, <DIGITAL LINK>, <DVI-D>,
<VIDEO>, <SDI>, <HDMI>) buttons
Switches the input signal to project.
Switches the input signal to project.
(SDI input is supported only for PT-RZ670.)
8 <FUNCTION>
button
Assigns a frequently used operation as a shortcut button.
9 Number (<0> - <9>) buttons
Used for entering an ID number or a password in a multiple
projector environment.
projector environment.
10 <AUTO SETUP> button
Automatically adjusts the image display position while projecting
the image.
[PROGRESS] is displayed while in automatic adjustment.
the image.
[PROGRESS] is displayed while in automatic adjustment.
11 <SHUTTER>
button
Used to temporarily turn off the image.
12 <TEST PATTERN> button
Displays the test pattern.
13 <STATUS>
button
Displays the projector information.
14 <DEFAULT>
button
Resets the content of the sub-menu to the factory default.
15 <ID SET> button
Sets the ID number of the remote control in a multiple projector
environment.
environment.
16 Remote control signal transmitter
17 Remote control wired terminal
This is the terminal used to connect to the projector via a cable
when used as a wired remote control.
when used as a wired remote control.
Attention
f Do not drop the remote control.
f Avoid contact with liquids or moisture.
f Do not attempt to modify or disassemble the remote control.
Note
f When operating the remote control by directly pointing at the remote control signal receiver of the projector body, operate the remote
control within a distance approx. 30 m (98'5") from the remote control signal receiver. The remote control can control at angles of up to ±30°
vertically and horizontally, but the effective control range may be reduced.
vertically and horizontally, but the effective control range may be reduced.
f If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.
f
f
. Use
it in a place distant from the light source.
f The power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.
f The operation of the <VIDEO> button is disabled in the factory default settings. The operation is enabled when [REMOTE CONTROL] is set
to [USER] and [VIDEO BUTTON] of [INPUT SELECT BUTTON] is set to other than [DISABLE], from the [SECURITY] menu
→ [CONTROL
DEVICE SETUP]
INF - 4
Click on the first or last page to see other PT-RZ670 / PT-RW630 (serv.man18) service manuals if exist.