Read Panasonic PT-RQ22KEJ (serv.man3) Service Manual online
INF-12
SECTION 1 SERVICE INFORMATION
< RQ22K >
SELF CHECK
OK : LD1 TEMP 123
OK : LD2 TEMP 123
OK : FPGA TEMP 123/456/789/123/456/789
3/4
OK : FPGA TEMP(SLOT1) 456
OK : FPGA TEMP(SLOT2) NONE
OK : LD1 1 1 1 1 1 1
OK : LD2 1 1 1 1 1 1
q�w CHANGE
DEVICE CHECK : OK
OK : FAN[1] 1111 1111 1111 1111 1111
OK : FAN[2] 1111 1
OK : PHOTO Y 123456.7(R=+123/G=+123/B=+123)
OK : PHOTO INIT
OK : ATM 1234.5/56.7
㉓ --- LD1 temperature check (Celsius)
㉔ --- LD2 temperature check (Celsius)
㉕ --- FPGA temperature check (Celsius)
㉖ --- SLOT1 Interface board FPGA temperature check (Celsius)
㉗ --- SLOT2 Interface board FPGA temperature check (Celsius)
㉘ --- LD1 check (1: normal / 0: abnormal / *: intentional Off)
㉙ --- LD2 check (1: normal / 0: abnormal / *: intentional Off)
㉚ --- Fan [1] check (1: normal / 0: abnormal)
㉛ --- Fan [2] check (1: normal / 0: abnormal)
㉜ --- Luminance sensor check (detected value)
㉝ --- Luminance sensor check (initial value)
㉞ --- Atmospheric pressure sensor check (hPa/Celsius)
㉔ --- LD2 temperature check (Celsius)
㉕ --- FPGA temperature check (Celsius)
㉖ --- SLOT1 Interface board FPGA temperature check (Celsius)
㉗ --- SLOT2 Interface board FPGA temperature check (Celsius)
㉘ --- LD1 check (1: normal / 0: abnormal / *: intentional Off)
㉙ --- LD2 check (1: normal / 0: abnormal / *: intentional Off)
㉚ --- Fan [1] check (1: normal / 0: abnormal)
㉛ --- Fan [2] check (1: normal / 0: abnormal)
㉜ --- Luminance sensor check (detected value)
㉝ --- Luminance sensor check (initial value)
㉞ --- Atmospheric pressure sensor check (hPa/Celsius)
Sensor
PCB
Ref No.
Luminance
M3
SN1401
Atmospheric pressure
RM
IC1501
Angle
A
IC3751
SELF CHECK
OK : ANGLE H -123.45/ V +123.45
OK : SHUTTER 12345 [ 0]
4/4
q�w CHANGE
DEVICE CHECK : OK
㉟ --- Angle sensor check (Horizontal angle / Vertical angle)
㊱ --- Shutter control check (Operating times [Failure times])
㊱ --- Shutter control check (Operating times [Failure times])
㊲ --- Device check (OK: Normal, NG: abnormal)
• Items ⑳ to ㊲ indicates the status of "NG" or "OK". If the "NG" indicates in red, the projector has an abnormal-
ity now. If the "OK" indicates in red, the projector had an abnormality in the past and operates normally now.
• To clear the error status, press the [MENU] button in the SELF CHECK mode, the confirmation window will
appear and select [OK] and press the [ENTER] button.
• This must be done after finishing the repair or maintenance.
CLEAR ERROR INFOMATION ?
OK
CANCEL
EXECUTE
CHANGE
ENTER
Click on the first or last page to see other PT-RQ22KEJ (serv.man3) service manuals if exist.