Read Panasonic PT-RQ22KEJ (serv.man3) Service Manual online
INF-2
SECTION 1 SERVICE INFORMATION
< RQ22K >
1. The name of each part
1. 1. Remote control
1
2
2
6
4
7
5
8
9
10
3
13
12
11
20
14
15
16
15
16
23
17
18
19
18
19
21
22
Front
Top
Bottom
A strap can be attached
depending on the usage.
1 Remote control indicator
Blinks if any button in the remote control is pressed.
2 Power on <b> button
Sets the projector to projection mode when the <MAIN
POWER> switch on the projector is set to <ON> and the power
is turned off (standby mode).
3 Power standby <v> button
Sets the projector to the state where the projector is turned
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
4 <MENU> button/<ENTER> button/asqw buttons
Used to navigate through the menu screen.
5 <ON SCREEN> button
5 <ON SCREEN> button
Switches the on‑screen display function on (display) or
off (hide).
6 <AUTO SETUP> button
Automatically adjusts the image display position while projecting
the image.
[PROGRESS] is displayed while in automatic adjustment.
7 <ASPECT> button
Switches the aspect ratio of the image.
8 Number (<0> - <9>) buttons
8 Number (<0> - <9>) buttons
Used for entering an ID number or a password in a multiple
projector environment.
9 <STATUS> button
Displays the projector information.
10 <LIGHT> button
Pressing this button lights up the remote control buttons. The
lights will go off when the remote control operation goes idle for
10 seconds.
11 <INPUT MENU> button
Displays the input selection screen.
12 Input selection buttons (<RGB1>, <RGB2>, <VIDEO>,
<S-VIDEO Y/C>, <DIGITAL LINK>, <DVI-D>, <HDMI>, <SDI>)
Switches the input signal to project.
The <DISPLAY PORT> button, the <SLOT1> button, and the
<SLOT2> button are not used with the projector.
13 <SHUTTER> button
Used to temporarily turn off the image.
14 <TEST PATTERN> button
14 <TEST PATTERN> button
Displays the test pattern.
15 Lens buttons (<FOCUS>, <ZOOM>, <SHIFT>)
Adjusts the focus, zoom, and lens shift.
16 <FUNCTION> button
16 <FUNCTION> button
Assigns a frequently used operation as a shortcut button. )
17 <DEFAULT> button
Resets the content of the sub-menu to the factory default.
18 <ID SET> button
Sets the ID number of the remote control in a multiple
projector environment.
19 <ID ALL> button
Used to simultaneously control all the projectors with a
single remote control in a multiple projector environment.
20 <LOCK> button
Used to prevent unintended operation by careless pressing of
the buttons and prevent draining the remote control batteries.
Operation of each button on the remote control is disabled by
sliding the <LOCK> button toward the arrow.
21 Remote control signal transmitter
22 Remote control wired terminal
22 Remote control wired terminal
This is a terminal used to connect to the projector via a cable
when the remote control is used as a wired remote control.
23 Strap hole
Note
f
When operating the remote control by directly pointing the remote control signal receiver of the projector, operate the remote control at
a distance approx. 30 m (98'5") or shorter from the remote control signal receiver. The remote control can control at angles of up to ±15°
vertically and ±30° horizontally, but the effective control range may be reduced.
f
If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.
f
The signal will be reflected off the screen. However, the operating range may be limited from light reflection loss due to the screen material.
f
If the remote control signal receiver directly receives strong light, such as fluorescent light, the remote control may not operate properly. Use
it in a place distant from the light source.
f
The power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.
Click on the first or last page to see other PT-RQ22KEJ (serv.man3) service manuals if exist.