PT-RQ22KEJ (serv.man2) - Panasonic Projector Service Manual (repair manual). Page 3

Read Panasonic PT-RQ22KEJ (serv.man2) Service Manual online

DIA-3
BLOCK & SCHEMATIC DIAGRAMS
< RQ22K series >
7
  印の部品は、安全上重要な部品です。交換をする時は、安全及び性能維持のため必ず指定の部品を使用してください。
補修部品一覧表の安全欄をよく確認してください。
Components identified by the international symbol 7 have special characteristics important for safety.
When replacing any of these components, use only the manufacturer's specified ones.
Important Safety Notice
■ Notes
1. HOT and COLD indications
  The power circuit board contains a circuit area using a separate power supply to isolate the ground connection.
  The circuit is defined by HOT and COLD indications in the schematic diagram. Take the precautions below:
   - NEVER touch the HOT part or the HOT and COLD parts at the same time, or you may get an electric shock.
   - NEVER short-circuit the HOT and COLD circuits, or the fuse may blow and the parts may break.
   - NEVER connect an instrument such oscilloscope to the HOT and COLD circuit simultaneously, or the fuse may blow.  
     Connect the ground of instruments to the ground of the circuit being measured.
2. MAKE SURE to unplug the power cord from the power outlet before disassembly, parts replacement and assembly.
3. This schematic diagram is the latest at the time of printing and the subject to change without notice.
4. Be sure to make your orders of replacement parts according to parts list section.
警 告
ご注意
    1. 充電部に触れたり、非充電部と同時に触れないでください。同時に触れたりすると感電することがあります。
     - 充電部は点線で区分しています。AC100Vが加わっていますので、点検・修理時は感電しないよう十分ご注意ください。
   
 - 充電部と非充電部をショートさせないでください。ヒューズが断線したり部品をこわすことがあります。
   
 - オシロスコープ等の測定器で充電部と非充電部を同時に測定しないでください。ヒューズが断線することがあります。
   
 - 一次側(充電部)の電圧・波形は一次側のアースを基準に測定してください。
    2. 分解、組み立て、部品交換は電源プラグを抜いて作業を行ってください。感電やけがをすることがあります。
    3. この回路図は、性能向上その他により実際の配線と異なる場合があります。
    4. 部品注文の際は、補修パーツリストで部品品番を確認してください。
■ 注释
1. HOT 与 COLD 指示
  电源电路板包含一个使用单独电源以绝缘接地连接的电路区域。此区域在原理图上通过HOT和COLD标识进行标注。
  采取以下预防措施。
   - 切勿触摸 HOT部品或同时触摸HOT和COLD部品,否则可能引起触电。
    - 切勿使HOT和COLD电路短路,否则保险丝可能烧断,引起部品损坏。
    - 切勿同时连接诸如示波器等仪器至HOT和COLD电路上,否则保险丝可能烧断。将仪器的接地端与测量电路的接地端连接。
2. 维修前,请务必关闭主电源并从电源插座上拔下电源插头。
3. 此原理图印刷时为最新版本,但如有更改恕不另行通知。
4. 务必根据部品清单,预订可更换部件。
标注有国际安全部品标识
 7 的元件均具备特殊安全特性。更换此种元件时,仅限使用制造商指定部品。 
重要安全提示
Page of 49
Display

Click on the first or last page to see other PT-RQ22KEJ (serv.man2) service manuals if exist.