Read Panasonic PT-RQ13K (serv.man2) Service Manual online
2
PREFACE
< RQ13K >
The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this service manual.
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to ser-
vice or repair the product or products dealt with in this service information by anyone else could result in serious injury or death.
WARNING : Use laser Light Radiation eye and skin protection during servicing
AVERTISSEMENT : Utilisez laser lumière oeil radioprotection et la protection de la peau lors de l'entretien
Notice on laser
This projector is the Class 1 laser product that complies with IEC 60825-1.
TQFX609
ョㄐㄓチワㄐㄓㄕㄉチモㄎㄆㄓㄊチ
éヤㄐㄎㄑㄍㄊㄆㄔチㄘㄊㄕㄉチビヒチヤョンチヱㄓㄕㄔチヒパフパハヒパチㄏㄅチヒパフパハヒヒ
ㄆㄙㄆㄑㄕチㄇㄐㄓチㄅㄆㄗㄊㄕㄊㄐㄏㄔチㄑㄖㄓㄔㄖㄏㄕチㄕㄐチロㄔㄆㄓチワㄐㄕㄊㄆ
ワㄐハブパチㄅㄕㄆㄅチㄋㄖㄏㄆチビフハビパパヘê
リユヤチプパベビブノヒホビパパヘ
ロモヴユンチンモュリモヵリヰワ
モヷヰリュチュリンユヤヵチユヺユチユヹヱヰヴヶンユ
ヤロモヴヴチピンチロモヴユンチヱンヰュヶヤヵ
ヸモヷユチロユワヨヵラホフフベノフプビㄏㄎ
ヮモヹリヮヶヮチヰヶヵヱヶヵホピピピㄎヸ
リユヤチプパベビブノヒホビパパヘ
ンモヺヰワワユヮユワヵチロモヴユン
ユヹヱヰヴリヵリヰワチュリンユヤヵユチュモワヨユンユヶヴユチヱヰヶンチロユヴチヺユヶヹ
モヱヱモンユリロチチロモヴユンチュユチヤロモヴヴユチピン
ロヰワヨヶユヶンヴチュトヰワュユヴホフフベノフプビㄏㄎ
ヮモヹリヮモロユチュヶチンモヺヰワワユヮユワヵホピピピㄎヸ
The class 4 laser module is mounted in the inside of a product.
TQFX608
ュモワヨユンノヤロモヴヴチフチロモヴユンチンモュリモヵリヰワチヸラユワチヰヱユワチモヷヰリュチユヺユチヰン
チチチチチチチチチチチチチチチチチチチヴレリワチユヹヱヰヴヶンユチヵヰチュリンユヤヵチヰンチヴヤモヵヵユンユュチンモュリモヵリヰワ
ュモワヨユンノンモヺヰワワユヮユワヵチロモヴユンチュユチヤロモヴヴユチフチノチユワチヤモヴチュトヰヶヷユンヵヶンユチ
ュモワヨユンノンモヺヰワワユヮユワヵチロモヴユンチュユチヤロモヴヴユチフチノチユワチヤモヴチュトヰヶヷユンヵヶンユチ
チチチチチチチチチチチチチチチチチチユヹヱヰヴリヵリヰワチュモワヨユンユヶヴユチモヶチンモヺヰワワユヮユワヵチュリンユヤヵチヰヶチ
チチチチチチチチチチチチチチチチチチュリョョヶヴチュユヴチヺユヶヹチヰヶチュユチロモチヱユモヶ
CAUTION
Lithium
Battery
Risk of explosion if battery is replaced by an incorrect type,
Replace only with the same of equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
About lead free solder (PbF)
This projector is using the P.C.Board which applies lead free solder.
Use lead free solder in servicing from the standpoint of antipollution for the global environment.
Notes:
• Lead free solder: Sn-Ag-Cu (tin, silver and copper) has a higher melting point (approx. 217°C) than standard solder Typically
the melting point is 30~40 °C higher. When servicing, use a high temperature soldering iron with temperature limitation func-
tion and set it to 370 ± 10 °C.
• Be precautious about lead free solder. Sn-Ag-Cu (tin, silver and copper) will tend to splash when heated too high (approx.
600°C or higher).
• Use lead free solder for the P.C.Board (specified on it as “PbF”) which uses lead free solder. (When you unavoidably use lead
solder, use lead solder after removing lead free solder. Or be sure to heat the lead free solder until it melts completely, before
applying lead solder.)
• After solder to double layered P.C Boards, check the component side for excess solder which may flow onto the opposite side.
About the identification of the lead free solder P.C.Board.
For the P.C.Board which applies lead free solder, the symbol as shown in the figure below is printed or stamped on the surface
or the back of P.C.Board.
PbF
Click on the first or last page to see other PT-RQ13K (serv.man2) service manuals if exist.