Read Panasonic PT-RCQ10 / PT-RCQ80 (serv.man3) Service Manual online
INF-2
SECTION 1 SERVICE INFORMATION
< RCQ10 / RCQ80 >
1. The name of each part
1. 1. Remote controls
1
3
2
4
5
5
7
8
8
6
9
10
11
16
13
12
14
15
17
18
Front
Top
Bottom
1 Power standby <v> button
Sets the projector to the state where the projector is turned
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
2 Power on <b> button
Sets the projector to projection mode when the <MAIN
POWER> switch on the projector is set to <ON> and the power
is turned off (standby mode).
3 Remote control indicator
Blinks if any button in the remote control is pressed.
4 Lens buttons (<FOCUS>, <ZOOM>, <SHIFT>)
Adjusts the focus, zoom, and lens shift.
(x page 77)
5 <MENU> button/<ENTER> button/asqw buttons
Used to navigate through the menu screen.
(x page 87)
asqw
buttons are also used to enter the password in
[SECURITY] or enter characters.
6 <ON SCREEN> button
Switches the on-screen display function on (display) or
off (hide).
(x page 83)
7 <INPUT MENU> button
Displays the input selection screen.
(x page 76)
8 Input selection buttons (<DIGITAL LINK>, <DVI-D>,
<SLOT>, <SDI>, <HDMI>)
Switches the input signal to project.
(x page 75)
The <SLOT> button can be used when the optional Interface
Board equipped with corresponding input is installed in the slot.
9 <FUNCTION> button
Assigns a frequently used operation as a shortcut button.
When the <FUNCTION> button is held down, the
[FUNCTION BUTTON] screen is displayed.
(x page 162)
10 Number (<0> - <9>) buttons
Used for entering an ID number or a password in a multiple
projector environment.
11 <AUTO SETUP> button
Automatically adjusts the image display position and signal level
while projecting the image.
[PROGRESS] is displayed while in automatic adjustment.
12 <SHUTTER> button
Used to temporarily turn off the image.
13 <TEST PATTERN> button
13 <TEST PATTERN> button
Displays the test pattern.
14 <STATUS> button
Displays the projector information.
15 <DEFAULT> button
Resets the setting of the displayed sub-menu to the factory
default.
16 <ID SET> button
Sets the ID number of the remote control in a multiple
projector environment.
17 Remote control signal transmitter
18 Remote control wired terminal
18 Remote control wired terminal
This is a terminal used to connect to the projector via a cable
when the remote control is used as a wired remote control.
Note
f
When operating the remote control by directly pointing at the remote control signal receiver of the projector, operate the remote control
within a distance approximately 30 m (98'5") from the remote control signal receiver. The remote control can control at angles of up to ±30°
vertically and horizontally, but the effective control range may be reduced.
f
If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.
f
The signal will be reflected off the screen. However, the operating range may be limited from light reflection loss due to the screen material.
f
If the remote control signal receiver directly receives strong light, such as fluorescent light, the remote control may not operate properly. Use
it in a place distant from the light source.
f
The power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.
Click on the first or last page to see other PT-RCQ10 / PT-RCQ80 (serv.man3) service manuals if exist.