Read Panasonic PT-LW330 / PT-LW280 / PT-LB360 / PT-LB330 / PT-LB300 / PT-LB280 (serv.man2) Service Manual online
-12-
Maintenance
Lamp Unit
The lamp unit is a consumable component. Refer to "When to replace the lamp
unit" for details about the replacement cycle.
When purchasing the optional Replacement Lamp Unit (Model No.: ET-LAL500),
consult your dealer.
The lamp unit is a consumable component. Refer to "When to replace the lamp
unit" for details about the replacement cycle.
When purchasing the optional Replacement Lamp Unit (Model No.: ET-LAL500),
consult your dealer.
Caution
Do not replace the lamp unit when it is hot. (Wait at least 1 hour after use.)
The inside of the cover can become very hot, table care to avoid burn injuries.
The inside of the cover can become very hot, table care to avoid burn injuries.
J
Notes on the replacement of the lamp unit
● A cross head screwdriver is necessary when replacing the lamp unit.
● Since the luminous lamp is made of glass, it may burst if it drops or hit with a hard object. Handle with care.
● Do not disassemble or modify the lamp unit.
● When replacing the lamp unit, be sure to hold it by the handle because its surface is pointed and its shape is
protruded.
protruded.
● The lamp may rapture. Replace the lamp unit carefully so the glass fragments of the lamp do not scatter. While
attaching the projector to the ceiling, do not work right under the lamp unit or do not conduct work while your face
is near the lamp unit.
attaching the projector to the ceiling, do not work right under the lamp unit or do not conduct work while your face
is near the lamp unit.
● The lamp contains mercury. When disposing of used lamp units, contact your local authorities or dealer for correct
methods of disposal.
methods of disposal.
Caution
● Panasonic takes no responsibility for any damage or malfunction of the product resulting from use of lamp units
which are not manufactured by Panasonic. Use only specified lamp units.
which are not manufactured by Panasonic. Use only specified lamp units.
● The model numbers of accessories and optional accessories are subject to change without prior notice.
J
When to replace the lamp unit
The lamp unit is a consumable component. Since its brightness gradually decreases over time, it is necessary to
replace the lamp unit regularly.
Please refer to the displayed time in [Lamp counter] of [Info.] about the usage time of lamp .
The estimated duration before replacement is 6 000 hours which is displayed in [Lamp counter], but the lamp may
go off before the time above mentioned has elapsed depending on individual lamp characteristics, usage conditions,
and the installation environment. It is recommended that the Replacement lamp unit be prepared earlier.
The time which is displayed in [Lamp counter] is a total time when the real usage time in [ (Normal)], [ (Eco 1)]
or [ (Eco 2)] is converted to the runtime in [ (Eco 1)]. Please note that they are not displayed individually.
The displayed time in [Lamp counter] = "Lamp runtime of [ (Normal)]" × 1.2 +"Lamp runtime of [ (Eco 1)]"
+ "Lamp runtime of [ (Eco 2)]" × 0.75
The real usage time when the displayed time in [Lamp counter] is 6 000 hours means,
When [Lamp control] is constantly set to [ (Normal)] without switching to other modes = 5 000 hours
When [Lamp control] is constantly set to [ (Eco 1)] without switching to other modes = 6 000 hours
When [Lamp control] is constantly set to [ (Eco 2)] without switching to other modes = 8 000 hours
If you continue to use the lamp unit after the displayed time in Lamp counter 6 600 hours has elapsed, the lamp
turns off automatically at approximately 10 minutes after turning on the power, as it will cause malfunction of the
projector.
replace the lamp unit regularly.
Please refer to the displayed time in [Lamp counter] of [Info.] about the usage time of lamp .
The estimated duration before replacement is 6 000 hours which is displayed in [Lamp counter], but the lamp may
go off before the time above mentioned has elapsed depending on individual lamp characteristics, usage conditions,
and the installation environment. It is recommended that the Replacement lamp unit be prepared earlier.
The time which is displayed in [Lamp counter] is a total time when the real usage time in [ (Normal)], [ (Eco 1)]
or [ (Eco 2)] is converted to the runtime in [ (Eco 1)]. Please note that they are not displayed individually.
The displayed time in [Lamp counter] = "Lamp runtime of [ (Normal)]" × 1.2 +"Lamp runtime of [ (Eco 1)]"
+ "Lamp runtime of [ (Eco 2)]" × 0.75
The real usage time when the displayed time in [Lamp counter] is 6 000 hours means,
When [Lamp control] is constantly set to [ (Normal)] without switching to other modes = 5 000 hours
When [Lamp control] is constantly set to [ (Eco 1)] without switching to other modes = 6 000 hours
When [Lamp control] is constantly set to [ (Eco 2)] without switching to other modes = 8 000 hours
If you continue to use the lamp unit after the displayed time in Lamp counter 6 600 hours has elapsed, the lamp
turns off automatically at approximately 10 minutes after turning on the power, as it will cause malfunction of the
projector.
The displayed
time in [Lamp
counter]
On-screen display
<WARNING> indicator
Over 5 700 hours
less than 6 000
hours
The lamp replacement icon
is displayed for 10
seconds. If you press any button within 10 seconds, the
icon disappears.
icon disappears.
The lamp replacement icon
will display for 4 seconds
on the screen after switching the input source or turning on
the projector.
the projector.
--
Over 6 000 hours
less than 6 600
hours
The lamp replacement warning icon
is
displayed for 10 seconds. If you press any button within 10
seconds, the icon disappears.
seconds, the icon disappears.
The lamp replacement warning icon
will
display for 4 seconds on the screen after switching the input
source or turning on the projector.
source or turning on the projector.
Lighting in red. (The indicator will
not light in the standby mode)
The displayed
time in [Lamp
counter]
On-screen display
<WARNING> indicator
Over 6 600 hours
The lamp replacement warning icon
is
displayed for 10 seconds. If you press any button within 10
seconds, the icon disappears.
seconds, the icon disappears.
The lamp replacement warning icon
will
display for 4 seconds on the screen after switching the input
source or turning on the projector.
source or turning on the projector.
The lamp automatically turns off at approximately 10
minutes after turning on the power.
Blinking in red. (The indicator will
not light in the standby mode)
J
Replacing the Unit
Click on the first or last page to see other PT-LW330 / PT-LW280 / PT-LB360 / PT-LB330 / PT-LB300 / PT-LB280 (serv.man2) service manuals if exist.