Read Panasonic PT-JW130GWE / PT-JW130GBE (serv.man2) Service Manual online
SECTION 1 SERVICE INFORMATION
<PT-JW130>
1. 4. Remote control
1
12
13
14
15
17
16
3
2
4
5
6
9
8
7
10
11
1 Remote control signal transmitter
2 Power
<
v/b> button
Turns on/off the power of the projector.
3 <Miracast>
button
Switches the input to Miracast.
When you press this button during the lighting mode, the mode
is switched to the projector mode, and the input is switched to
Miracast.
When you press this button during the lighting mode, the mode
is switched to the projector mode, and the input is switched to
Miracast.
4 <SIGNAGE>
button
Switches the input to signage.
When you press this button during the lighting mode, the mode
is switched to the projector mode, and the input is switched to
signage.
When you press this button during the lighting mode, the mode
is switched to the projector mode, and the input is switched to
signage.
5 <MEMORY VIEWER> button
Switches the input to Memory Viewer.
When you press this button during the lighting mode, the mode
is switched to the projector mode, and the input is switched to
Memory Viewer.
When you press this button during the lighting mode, the mode
is switched to the projector mode, and the input is switched to
Memory Viewer.
6
asqw buttons/<ENTER> button/<RETURN> button
Used to operate the menu screen. Also used when entering
[SECURITY PASSWORD].
Used to operate the menu screen. Also used when entering
[SECURITY PASSWORD].
7 <AV MUTE> button
Used to turn off the image and audio temporarily.
8 <DEFAULT>
button
Resets the settings of the sub-menu to the factory defaults.
9 <MENU>
button
Displays the main menu.
10 <ZOOM> button/<FOCUS> button
Displays the lens menu and adjusts the projection lens.
11 <VOL+>/<VOL-> buttons
Adjusts the volume of audio output.
12 <LIGHTING/PROJECTOR>
button
Switches the projection mode of the projector to lighting mode
or projector mode.
or projector mode.
13 <Panasonic
APP>
button
Switches the input to Panasonic APPLICATION.
When you press this button during the lighting mode, the mode
is switched to the projector mode, and the input is switched to
Panasonic APPLICATION.
When you press this button during the lighting mode, the mode
is switched to the projector mode, and the input is switched to
Panasonic APPLICATION.
14 <HDMI>
button
Switches the input to HDMI.
When you press this button during the lighting mode, the mode
is switched to the projector mode, and the input is switched to
HDMI.
When you press this button during the lighting mode, the mode
is switched to the projector mode, and the input is switched to
HDMI.
15 <ID
ALL>
button
Used to simultaneously control all the projectors with a
single remote control in a multiple projector environment.
single remote control in a multiple projector environment.
16 <ID SET> button
Sets the ID number of the remote control in a multiple projector
environment.
environment.
17 Number (<1> - <6>) buttons
Used in a multiple projector environment.
Used to enter ID number or password.
Used to enter ID number or password.
Attention
f Do not drop the remote control.
f Avoid contact with liquids or moisture.
f Do not attempt to modify or disassemble the remote control.
f Observe the following instructions that are indicated on the caution label at the back of the remote control:
g Do not use a new battery together with an old battery
g Do not use unspecified batteries.
The signal from the remote control can be reflected off the projection surface to operate the projector. However, the operating range may be
limited from light reflection loss or the shape of the projection surface.
limited from light reflection loss or the shape of the projection surface.
.
Note
f When operating the remote control by directly pointing to the remote control signal receiver at the power supply unit of the projector, operate
the remote control within a distance approximately 7 m (276") or shorter from the remote control signal receiver. The remote control can
control at angles of up to ±30° vertically and horizontally, but the effective control range may be reduced.
control at angles of up to ±30° vertically and horizontally, but the effective control range may be reduced.
f If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.
f
f The remote control may not operate properly if the remote control signal receiver on the power supply unit of the projector is directly
receiving strong light, such as fluorescent light. Install the projector in a place distant from the light source.
INF - 4
Click on the first or last page to see other PT-JW130GWE / PT-JW130GBE (serv.man2) service manuals if exist.