Read Panasonic PT-DZ870T / PT-DW830T / PT-DX100T / PT-DZ870U / PT-DZ870E / PT-DW830U / PT-DW830E / PT-DX100U / PT-DX100E (serv.man4) Service Manual online
3
■
Cautions when transporting
・When transporting the projector, move the lens position to the home position and attach the lens cushion.
If lens optional model, move the lens position to the home position, remove the projection lens, and then attach
the lens hole cover.
・When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts.
・When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts.
They may damage the internal components and result in malfunctions.
・Do not transport the projector with the adjustable feet extended.
・Do not transport the projector with the adjustable feet extended.
Doing so may damage the adjustable feet.
■
Do not set up the projector in the following locations.
・Places where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal
components or malfunction.
・Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare cases
・Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare cases
due to the heated air from the air exhaust port or the hot or cooled air. Make sure that the exhaust from the projector
or other equipment, or the air from the air conditioner does not blow toward the front of the projector.
・Places with sharp temperature fluctuations such as near lights (studio lamps): Doing so may shorten the life
・Places with sharp temperature fluctuations such as near lights (studio lamps): Doing so may shorten the life
of the lamp, or result in deformation of the outer case due to heat, which may cause malfunctions.
The operating environment temperature of the projector should be between 0 °C (32 °F) and 45 °C (113 °F) when
using it at elevations lower than 1 400 m (4 593') above sea level, and between 0 °C (32 °F) and 40 °C (104 °F) when
using it at high altitudes (1 400 m (4 593') or higher – lower than 2 700 m (8 858') above sea level).
If you use the Smoke cut filter, the operating environment temperature should be between 0 °C (32 °F) and
35 °C (95 °F). However, it cannot be used at high altitudes.
If you use the Replacement lamp unit (for portrait mode), the operating environment temperature should be between
0 °C (32 °F) and 40 °C (104 °F) when using the projector at elevations lower than 1 400 m (4 593') above sea level,
and between 0 °C (32 °F) and 35 °C (95 °F) when using the projector at high altitudes. If you use the Smoke cut filter
together, the operating environment temperature should be between 0 °C (32 °F) and 30 °C (86 °F).
・Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.
・Places where there is high-power laser equipment: Directing a laser beam onto the lens surface causes damage
・Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.
・Places where there is high-power laser equipment: Directing a laser beam onto the lens surface causes damage
to the DLP chips.
■
Note at the time of installation
・The high clarity projection lens is thermally affected by the light from the light source, making the focus unstable in
the period just after switching on the power. Wait at least 30 minutes with the image projected before adjusting
the period just after switching on the power. Wait at least 30 minutes with the image projected before adjusting
the lens focus.
・Make sure to set [HIGH ALTITUDE MODE] to [ON] when using the projector at elevations between 1 400 m (4 593')
・Make sure to set [HIGH ALTITUDE MODE] to [ON] when using the projector at elevations between 1 400 m (4 593')
or higher and lower than 2 700 m (8 858') above sea level.
Do not install the projector at elevations of 2 700 m (8 858') or higher above sea level.
・Do not use the projector tilted to the right or left.
・Set [COOLING CONDITION] according to the projection direction, but set it to [AUTO] most commonly.
・Do not use the projector tilted to the right or left.
・Set [COOLING CONDITION] according to the projection direction, but set it to [AUTO] most commonly.
Using the projector with [COOLING CONDITION] set incorrectly may shorten the life of the lamp.
Check the setting from [COOLING CONDITION] on the [STATUS] screen.
Click on the first or last page to see other PT-DZ870T / PT-DW830T / PT-DX100T / PT-DZ870U / PT-DZ870E / PT-DW830U / PT-DW830E / PT-DX100U / PT-DX100E (serv.man4) service manuals if exist.