Read Panasonic PT-DZ780 / PT-DW750 / PT-DX820 / PT-DZ780BE / PT-DZ780LBE / PT-DZ780LWE / PT-DZ780WE / PT-DW750BE / PT-DX820BE / PT-DX820LBE (serv.man6) Service Manual online
ET‑LAD70W (2 pcs)
WD: White model, the standard zoom lens supplied
LBD: Black model, the lens sold separately
LWD: White model, the lens sold separately
W: White model, the standard zoom lens supplied
LB: Black model, the lens sold separately
LW: White model, the lens sold separately
PT-DW750
PT-DX820
Use lead free solder in servicing from the standpoint of antipollution for the global environment.
Notes:
・ Be precautious about lead free solder. Sn-Ag-Cu (tin, silver and copper) will tend to splash when heated too high (approx. 600°C or higher).
・ Use lead free solder for the P.C.Board (specified on it as “PbF”) which uses lead free solder. (When you unavoidably use lead solder, use lead
・ solder after removing lead free solder. Or be sure to heat the lead free solder until it melts completely, before applying lead solder.)
・ After soldering to double layered P.C.Boards, check the component side for excess solder which may flow onto the opposite side.
For the P.C.Board which applies lead free solder, the symbol as shown in the figure below is printed or stamped on the surface
or the back of P.C.Board.
with manufacturer’s specified parts to prevent shock, fire, or other hazards. Do not modify the original design without permission of
manufacturer.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
or repair the product or products dealt with in this service information by anyone else could result in serious injury or death.
Replace only with the same of equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
If lens optional model, move the lens position to the home position, remove the projection lens, and then attach
the lens hole cover.
They may damage the internal components and result in malfunctions.
Doing so may damage the adjustable feet.
components or malfunction.
Also, it may shorten the life of the components and result in malfunctions.
due to the heated air from the air exhaust port or the hot or cooled air. Make sure that the exhaust from the projector
or other equipment, or the air from the air conditioner does not blow toward the front of the projector.
of the lamp, or result in deformation of the outer case due to heat, which may cause malfunctions.
The operating environment temperature of the projector should be between 0 °C (32 °F) and 45 °C (113 °F) when
using it at elevations lower than 1 400 m (4 593') above sea level, and between 0 °C (32 °F) and 40 °C (104 °F) when
using it at high altitudes (between 1 400 m (4 593') and 2 700 m (8 858') above sea level).
to the DLP chips.
the period just after switching on the power. It is recommended that images be projected continuously for at least
30 minutes before the focus is adjusted.
Using the projector at a vertical angle that exceeds ±15° may reduce product life or result in malfunction.
2. Specifications
2. OSD Menu Navigation
3. Service Mode
4. Notes on service
5. Troubleshooting
2. Disassembly Instructions
2. Software update procedure
2. Interconnection Block Diagram
3. Schematic Diagram
4. Circuit Boards Diagram