PT-DZ16KU, PT-DZ16KE, PT-DS16KD (serv.man13) - Panasonic Projector Service Manual (repair manual). Page 2

Read Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man13) Service Manual online

The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this service manual.
    Lithium Battery
    About lead free solder (PbF)
This projector is using the P.C.Board which applies lead free solder.
Use lead free solder in servicing from the standpoint of antipollution for the global environment.
  This service information is designed for experienced repair technicians only and is not designed for use by the general public.
  It dose not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
  Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
  or repair the product or products dealt with in this service information by anyone else could result in serious injury or death.
WARNING : Use UV Radiation eye and skin protection during servicing
If using of this projector at high altitudes (above 1,400m), set HIGHT ALTITUDE MODE to “ON”.
(Refer to “PROJECTOR SETUP menu” in Operating Instructions.)
Failure to observe this may cause malfunctions. Never use this projector at an altitude of 2,700m or higher.
Using this projector at high altitude, consult your dealer or Authorized Service Center about preparations.
Risk of explosion if battery is replaced by an incorrect type,
Replace only with the same of equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
AVERTISSEMENT : Utilisez UV œil radioprotection et la protection de la peau lors de l'entretien
For US
Any unauthorized changes or modifications to this equipment will void the users authority to operate.
 Lead free solder: Sn-Ag-Cu (tin, silver and copper) has a higher melting point (approx. 217°C) than standard solder. Typically the melting point
  ・ is 30~40 °C higher. When servicing, use a high temperature soldering iron with temperature limitation function and set it to 370 ± 10 °C.
  ・ Be precautious about lead free solder. Sn-Ag-Cu (tin, silver and copper) will tend to splash when heated too high (approx. 600°C or higher).
  ・ Use lead free solder for the P.C.Board (specified on it as “PbF”) which uses lead free solder. (When you unavoidably use lead solder, use lead
  ・ solder after removing lead free solder. Or be sure to heat the lead free solder until it melts completely, before applying lead solder.)
  ・ After soldering to double layered P.C.Boards, check the component side for excess solder which may flow onto the opposite side.
About the identification of the lead free solder P.C.Board.
  For the P.C.Board which applies lead free solder, the symbol as shown in the figure below is printed or stamped on the surface
  or the back of P.C.Board.
 There are special parts used in Panasonic DLP Projectors which are important for safety. These parts are shaded on the schematic
 diagram. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire, or other
 hazards. Do not modify the original design without permission of Panasonic System Communications Company of North America.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
Page of 110

Click on the first or last page to see other PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man13) service manuals if exist.