Read Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man10) Service Manual online
PREFACE
<PT-DZ16K>
■
Cautions when transporting
・
When transporting the projector, remove the projection lens before attaching the dust sponge.
Otherwise dust will accumulate inside and may cause malfunctions.
・
・
When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts.
They may damage the internal components and result in malfunctions.
・
・
Do not transport the projector with the adjustable feet extended.
Doing so may damage the adjustable feet.
■
Do not set up the projector in the following locations.
・
The projector is designed for indoor use only.
・
Places where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal
components or malfunction.
・
・
Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare cases
due to the heated air from the air exhaust port or the hot or cooled air. Make sure that the exhaust from the projector
or other equipment, or the air from the air conditioner does not blow toward the front of the projector.
・
or other equipment, or the air from the air conditioner does not blow toward the front of the projector.
・
Places with sharp temperature fluctuations such as near lights (studio lamps): Doing so may shorten the life
of the lamp, or result in deformation of the outer case due to heat, which may cause malfunctions.
The operating environment temperature of the projector should be between 0 °C (32 °F) and 45 °C (113 °F) when
using it at elevations lower than 1 400 m (4 593') above sea level, and between 0 °C (32 °F) and 40 °C (104 °F) when
using it at high altitudes (between 1 400 m (4 593') and 2 700 m (8 858') above sea level).
If you use the Smoke cut filter, the operating environment temperature should be between 0 °C (32 °F) and
35 °C (95 °F). However, it cannot be used at high altitudes.
・
The operating environment temperature of the projector should be between 0 °C (32 °F) and 45 °C (113 °F) when
using it at elevations lower than 1 400 m (4 593') above sea level, and between 0 °C (32 °F) and 40 °C (104 °F) when
using it at high altitudes (between 1 400 m (4 593') and 2 700 m (8 858') above sea level).
If you use the Smoke cut filter, the operating environment temperature should be between 0 °C (32 °F) and
35 °C (95 °F). However, it cannot be used at high altitudes.
・
Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.
・
Places where there is high-power laser equipment: Directing a laser beam onto the lens surface causes damage
to the DLP chips.
3
p
■
Note at the time of installation
・
The high clarity projection lens is thermally affected by the light from the light source, making the focus unstable in
the period just after switching on the power. Wait at least 30 minutes with the image projected before adjusting
the lens focus.
・
・
Make sure to set [HIGH ALTITUDE MODE] to [ON] when using the projector at elevations between 1 400 m (4 593')
and 2 700 m (8 858') above sea level.
Do not install the projector at elevations of 2 700 m (8 858') or higher above sea level.
・
Do not install the projector at elevations of 2 700 m (8 858') or higher above sea level.
・
Do not use the projector tilted to the right or left.
・
Do not install and use the projector in portrait setting.
3
Click on the first or last page to see other PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man10) service manuals if exist.