TX-PR65VT30 - Panasonic Plasma Service Manual (repair manual)

tx-pr65vt30 service manual
Model
TX-PR65VT30
Pages
127
Size
8.74 MB
Type
PDF
Document
Service Manual
Brand
Device
Plasma / GPF14D-E CHASSIS
File
tx-pr65vt30.pdf
Date

Read Panasonic TX-PR65VT30 Service Manual online

ORDER NO.PCZ1106111CE
Plasma Television
Model No.
TX-PR65VT30
GPF14D-E Chassis
2
TABLE OF CONTENTS
PAGE
PAGE
1 Safety Precautions -----------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Touch-Current Check--------------------------------------3
2 Warning --------------------------------------------------------------4
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------4
2.2. About lead free solder (PbF) ----------------------------5
3 Service Navigation------------------------------------------------6
3.1. PCB Layout--------------------------------------------------6
3.2. Applicable signals------------------------------------------7
4 Specifications ------------------------------------------------------8
5 Technical Descriptions---------------------------------------- 10
5.1. Specification of KEY for CI Plus, DTCP-IP,
WIDEVINE and One-to-One -------------------------- 10
5.2. Service port (M3 mini Jack) Specifications -------- 11
6 Service Mode ----------------------------------------------------- 14
6.1. How to enter into Service Mode ---------------------- 14
6.2. Option - Mirror--------------------------------------------- 16
6.3. Service tool mode---------------------------------------- 16
6.4. Hotel mode------------------------------------------------- 17
6.5. Data Copy by SD Card --------------------------------- 18
7 Troubleshooting Guide---------------------------------------- 21
7.1. Check of the IIC bus lines------------------------------ 21
7.2. Power LED Blinking timing chart --------------------- 22
7.3. No Power--------------------------------------------------- 23
7.4. No Picture -------------------------------------------------- 24
7.5. Local screen failure-------------------------------------- 25
8 Service Fixture & Tools --------------------------------------- 26
8.1. SC jig -------------------------------------------------------- 26
9 Disassembly and Assembly Instructions--------------- 27
9.1. Remove the Rear cover -------------------------------- 27
9.2. Remove the AC inlet ------------------------------------ 29
9.3. Remove the P(MAIN)-Board -------------------------- 29
9.4. Remove the P(SUS)-Board---------------------------- 29
9.5. Remove the P(SUB)-Board---------------------------- 29
9.6. Remove the Terminal covers and the shield
metals ------------------------------------------------------- 30
9.7. Remove the A-Board------------------------------------ 30
9.8. Remove the Side unit assy ---------------------------- 30
9.9. Remove the SU-Board---------------------------------- 31
9.10. Remove the SD-Board---------------------------------- 31
9.11. Remove the SC-Board---------------------------------- 31
9.12. Remove the SS-Board---------------------------------- 31
9.13. Remove the SS2-Board -------------------------------- 32
9.14. Remove the Fan------------------------------------------ 32
9.15. Remove the Speakers ---------------------------------- 32
9.16. Remove the Woofer ------------------------------------- 32
9.17. Remove the Stand bracket----------------------------- 33
9.18. Remove the K-Board------------------------------------ 33
9.19. Remove the S-Board------------------------------------ 33
9.20. Remove the V-Board ------------------------------------ 33
9.21. Remove the Handles------------------------------------ 33
9.22. Remove the Bottom cabinet assy-------------------- 34
9.23. Remove the Plasma panel section from the
Cabinet assy----------------------------------------------- 34
9.24. Remove the Contact metals --------------------------- 34
9.25. Remove the C1-Board ---------------------------------- 34
9.26. Remove the C2-Board ---------------------------------- 35
9.27. Remove the C3-Board --------------------------------- 35
9.28. Remove the AL frames--------------------------------- 35
9.29. Replace the Plasma panel ---------------------------- 35
10 Measurements and Adjustments -------------------------- 36
10.1. Adjustment ------------------------------------------------ 36
11 Block Diagram --------------------------------------------------- 45
11.1. Main Block Diagram------------------------------------- 45
11.2. Block (1/4) Diagram ------------------------------------- 46
11.3. Block (2/4) Diagram ------------------------------------- 47
11.4. Block (3/4) Diagram ------------------------------------- 48
11.5. Block (4/4) Diagram ------------------------------------- 49
12 Wiring Connection Diagram -------------------------------- 51
12.1. Caution statement. -------------------------------------- 51
12.2. Wiring (1) -------------------------------------------------- 51
12.3. Wiring (2) -------------------------------------------------- 52
12.4. Wiring (3) -------------------------------------------------- 53
12.5. Wiring (4) -------------------------------------------------- 54
13 Schematic Diagram
14 Printed Circuit Board
15 Exploded View
3
1 Safety Precautions
1.1.
General Guidelines
1. When conducting repairs and servicing, do not attempt to modify the equipment, its parts or its materials.
2. When wiring units (with cables, flexible cables or lead wires) are supplied as repair parts and only one wire or some of the
wires have been broken or disconnected, do not attempt to repair or re-wire the units. Replace the entire wiring unit instead.
3. When conducting repairs and servicing, do not twist the Fasten connectors but plug them straight in or unplug them straight
out.
4. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
5. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
6. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.2.
Touch-Current Check
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth ground
such as a water pipe, as shown in Figure 1.
3. Use Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reserve the AC plug in the AC outlet and repeat each of the above measure.
6. The potential at any point (TOUCH CURRENT) expressed as voltage U
1
 and U
2
, does not exceed the following values:
For a. c.: U
1
 = 35 V (peak) and U
2
 = 0.35 V (peak);
For d. c.: U
1
 = 1.0 V,
Note:
The limit value of U
2
 = 0.35 V (peak) for a. c. and U
1
 = 1.0 V for d. c. correspond to the values 0.7 mA (peak) a. c. and 2.0
mA d. c.
The limit value U
1
 = 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies greater than 100 kHz.
7. In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the customer.
Figure 1
4
2 Warning
2.1.
Prevention of Electrostatic Discharge (ESD) to Electrostatically 
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor [chip] components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as [anti-static (ESD protected)] can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals.   These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the brush-
ing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient
to damage an ES device).
Page of 127
Display

Download Panasonic TX-PR65VT30 Service Manual (Repair Manual)

Here you can read online and download Panasonic TX-PR65VT30 Service Manual in PDF. TX-PR65VT30 service manual will guide through the process and help you recover, restore, fix, disassemble and repair Panasonic TX-PR65VT30 Plasma. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.