Read Panasonic FZ-A1BDAAXXM / FZ-A1BDAAEE9 / FZ-A1BDAAZE9 Service Manual online
■ Attachment of Battery Mylar
(Note)
(Note)
(Note)
Apply the initial pressure in the order of
ԘЈԜ.
When using a pressure bar, apply pressure in the order of
ԛЈԜ.
Steps
ԙ and Ԛ are important to secure airtightness for adhesion.
If uneven color is found after pressure is applied, do not apply
pressure again because it is a cause of float and uneven pressure.
Please replace with a new sheet.
(For this two-sided tape, the first contact with the cabinet is important.
Adhesion power is decreased even if pressure is applied again later.)
pressure again because it is a cause of float and uneven pressure.
Please replace with a new sheet.
(For this two-sided tape, the first contact with the cabinet is important.
Adhesion power is decreased even if pressure is applied again later.)
Apply the initial pressure in the order of
ԘЈԜ.
When using a pressure bar, apply pressure in the order of
ԛЈԜ.
Steps
ԙ and Ԛ are important to secure airtightness for adhesion.
If uneven color is found after pressure is applied, do not apply
pressure again because it is a cause of float and uneven pressure.
Please replace with a new sheet.
(For this two-sided tape, the first contact with the cabinet is important.
Adhesion power is decreased even if pressure is applied again later.)
pressure again because it is a cause of float and uneven pressure.
Please replace with a new sheet.
(For this two-sided tape, the first contact with the cabinet is important.
Adhesion power is decreased even if pressure is applied again later.)
Apply the initial pressure in the order of
ԘЈԜ.
When using a pressure bar, apply pressure in the order of
ԛЈԜ.
Steps
ԙ and Ԛ are important to secure airtightness for adhesion.
If uneven color is found after pressure is applied, do not apply
pressure again because it is a cause of float and uneven pressure.
Please replace with a new sheet.
(For this two-sided tape, the first contact with the cabinet is important.
Adhesion power is decreased even if pressure is applied again later.)
pressure again because it is a cause of float and uneven pressure.
Please replace with a new sheet.
(For this two-sided tape, the first contact with the cabinet is important.
Adhesion power is decreased even if pressure is applied again later.)
1.
2.
3.
3.
1.
2.
3.
3.
1.
2.
3.
3.
Procedure
Ԝ
Pressing the center of Battery Mylar
with palm your hand, apply pressure
evenly with jig from right to
left, from bottom to top.
Allow the air in the sheet to escape
in the arrow direction.
with palm your hand, apply pressure
evenly with jig from right to
left, from bottom to top.
Allow the air in the sheet to escape
in the arrow direction.
Procedure
Ԛ
Next, apply pressure from this area
with jig and allow air to
escape in the arrow direction.
Pressure application in the
L character shape is complete.
(Uneven color is a sign of float and
uneven pressure.)
with jig and allow air to
escape in the arrow direction.
Pressure application in the
L character shape is complete.
(Uneven color is a sign of float and
uneven pressure.)
Procedure
Ԙ
Position the sheet at the bottom
right corner as it is floating.
Prevent the sheet from running
over the right wall and bottom wall.
right corner as it is floating.
Prevent the sheet from running
over the right wall and bottom wall.
Procedure
ԙ
If the position is determined, apply pressure to this
area with jig evenly preventing air from entering.
(Uneven color is a sign of float and uneven pressure.)
area with jig evenly preventing air from entering.
(Uneven color is a sign of float and uneven pressure.)
Procedure
ԛ
Pressing the center of Battery Mylar with palm
your hand, apply pressure evenly with jig from
right to left, from bottom to top.
your hand, apply pressure evenly with jig from
right to left, from bottom to top.
Attaching standard
Attaching standard
Once the Battery Mylar is removed,
visually check that there is no
adhesive deposit.
If adhesive deposit remains, remove
it with Scotch tape or eraser.
When using an eraser, remove the
rubber dust completely.
After that, wipe the adhesive side
with IPA (isopropyl alcohol) and dry
completely.
visually check that there is no
adhesive deposit.
If adhesive deposit remains, remove
it with Scotch tape or eraser.
When using an eraser, remove the
rubber dust completely.
After that, wipe the adhesive side
with IPA (isopropyl alcohol) and dry
completely.
(Preparation)
Open the DC cover,
HDMI cover or SMI
cover.
Reason: To prevent the
Battery Mylar floating.
HDMI cover or SMI
cover.
Reason: To prevent the
Battery Mylar floating.
NG
NG
Remove soil and oil on
the adhesive side using
PIA.
the adhesive side using
PIA.
Do not floating the Battery Mylar.
7-26
Click on the first or last page to see other FZ-A1BDAAXXM / FZ-A1BDAAEE9 / FZ-A1BDAAZE9 service manuals if exist.