Read Panasonic KV-SS905C / KV-SS905CCN Service Manual Supplement online
1 TOPICS OF MAIN CHANGED CONTENTS
Remarks
Important level codes for the following changed contents
· A: High
· B: Middle
· C: Low (Correction)
· A: High
· B: Middle
· C: Low (Correction)
Section No.
(Original Service
Manual)
Title on this Supplement
Main Contents
Remarks
1
2.1 “Section 1.2 Electrical Tests“
(Addition)
Add AC cord illustration for KV-SS905CCN.
Add AC cord illustration for KV-SS905CCN.
A
4
3.1 “Section 4.6.5 Color (Simplex/Duplex)“
(Modification)
Modify the value for Resolution 300 dpi.
Modify the value for Resolution 300 dpi.
A
4
3.2 “Section 4.10 Connecting the Unit to a
Personal Computer“
Personal Computer“
(Addition)
Add the following sentence on the Note.
Add the following sentence on the Note.
Be sure to use a SCSI cable as short as possible,
covered with shield.
B
4
3.3 “Section 4.11 System Requirements“
(Modification)
Add “®“ and “Windows
Add “®“ and “Windows
®
XP“
Modify the Memory Condition.
128MB or higher
128MB or higher
256MB or higher
A
4
3.4 “Section 4.13.2 Setting the ADF
Selector“
Selector“
(Modification)
Modify “(2)“ and “(3)“ sentences.
(2): ADF selector to “1“ or “2“
Modify “(2)“ and “(3)“ sentences.
(2): ADF selector to “1“ or “2“
ADF selector to “4“ or
“5“
(3): ADF selector to “4“ or “5“
(3): ADF selector to “4“ or “5“
ADF selector to “1“ or
“2“
A
5
4.1 “Section 5.3 Sensor (Boards)“
(Modification)
Modify the location bar positions.
Modify the location bar positions.
For Starting Position Sensor (S), Skew [L] Sensor (L),
Waiting Sensor (W), Double Feed Detector [Receiver],
Skew [R] Sensor (R), Edge Limit [R] Sensor (r)
Skew [R] Sensor (R), Edge Limit [R] Sensor (r)
B
7
5.1 “Section 7.5.1 Replacing the Paper
Feed Roller Module“
Feed Roller Module“
(Modification)
Modify the illustration for “(6)“ sentence.
(Near the “Paper Feed Roller Hole“ the illustration says)
Modify the illustration for “(6)“ sentence.
(Near the “Paper Feed Roller Hole“ the illustration says)
C
7
5.2 “Section 7.5.2 Replacing the Retard
Roller Module“
Roller Module“
(Modification)
Modify words in the illustration for sentences (1), (2)
Modify words in the illustration for sentences (1), (2)
(Inside the Front Door)
C
7
5.3 “Section 7.5.3 Replacing the Retard
Pad“
Pad“
(Modification)
Modify the sentences (3) and (7).
Modify words in the illustration for the sentence (3)
Modify the sentences (3) and (7).
Modify words in the illustration for the sentence (3)
Retard Roller Door
C
8
6.1 “Section 8.2.3 Left Side Panel“
(Modification)
Modify the location bar position for Screws in the
Illustration.
Modify the location bar position for Screws in the
Illustration.
C
8
6.2 “Section 8.2.10 Top Cover“
(Modification)
Modify words in the illustration.
Modify words in the illustration.
Screw and Washer
C
8
6.3 “Section 8.3.3 Board Box & Power Box“ (Modification)
Modify the sentence (3).
Disconnect all connectors on the MOTHER Board.
C
8
6.4 “Section 8.3.12 Conveyor Belt 2“
(Modification & Addition)
Reason: Addition of the process to remove the Side
Panel stay2
Reason: Addition of the process to remove the Side
Panel stay2
· Modify the sentences (4) and (5).
· Add words (Side Panel Stay2, Screw(C)) in the
· Add words (Side Panel Stay2, Screw(C)) in the
illustration.
B
8
6.5 “Section 8.3.13 Conveyor Belt 1“
(Modification & Addition)
Reason: Addition of the process to remove the Side
Panel stay2
Reason: Addition of the process to remove the Side
Panel stay2
· Modify the sentences (5) and (6).
· Add words (Side Panel Stay2, Screw(C)) in the
· Add words (Side Panel Stay2, Screw(C)) in the
illustration.
B
8
6.6 “Section 8.3.14 Paper Feed Belt“
(Modification)
Reason: Addition of the process to remove the Spring.
Reason: Addition of the process to remove the Spring.
· Modify the sentences (4) and (5).
B
8
6.7 “Section 8.4.7 POINTER Board, Exit
[Rear] Sensor“
[Rear] Sensor“
(Modification)
Reason: Addition of the process to remove the Conveyor
Upper 7 Assembly.
Reason: Addition of the process to remove the Conveyor
Upper 7 Assembly.
· Modify the sentence (3).
B
8
6.8 “Section 8.4.8 HOPPER [POSITION]
Board, HOPPER [ANGLE] Board“
Board, HOPPER [ANGLE] Board“
(Modification)
Modify the location bar (Screw (B)) position.
Modify the location bar (Screw (B)) position.
C
3
KV-SS905C / KV-SS905CCN
Click on the first or last page to see other KV-SS905C / KV-SS905CCN service manuals if exist.