Read Panasonic KV-S8147-M / KV-S8127-M / KV-S8150 / KV-S8130 / KV-S8120 Service Manual Supplement online
17
KV-S8147/KV-S8127/KV-S8150/KV-S8130/KV-S8120
Appendix 1
4. Background Plate (B) switching
is not working properly.
1. Execute "Focus" Test in Sec.10.3.7 to check
the peak level when Background Color is
White and Black.
White and Black.
2. Check the Background color in Image
Capture Plus
(Refer to "11 Troubleshooting Appendix 2" )
F63 (Back-side
black level error)
black level error)
53
00
00
00 1. Pixel data from CIS (B) or image
processing circuits have some
problems.
problems.
Refer 3rd item of Error Code F62.
F71 (Model ID Error)
9F
00
00
00 Model ID of Control Board does not
match the ID of Drive Board, Lower
Relay Board, Upper Relay board or
Panel Board.
Relay Board, Upper Relay board or
Panel Board.
1. Check the model name of the replaced board
from the part number.
2. Check the following connection and solder-
ing condition on each connector.
a. CN14 (Control Board) to CN2009 (Drive
a. CN14 (Control Board) to CN2009 (Drive
Board)
b. CN19 (Control Board) to CN3004 (Upper
Relay Board)
c.CN18 (Control Board) to CN3304 (Upper
Relay Board)
F80 (Double Feed
Detector
adjustment error)
Detector
adjustment error)
60
00
00
x
1. Double Feed Detector (G) does
not work correctly.
Refer to 5th item of Error U23.
Three sensor model(S8127/S8120)
ST4 0 : center, 1 : left, 2 : right
ST4 0 : center, 1 : left, 2 : right
Five sensor model(S8147/S8150/S8130)
ST4 0 : center, 1 : R1, 2 : L1, 3 : R2, 4 : L2
ST4 0 : center, 1 : R1, 2 : L1, 3 : R2, 4 : L2
2. Double Feed Detector (R) does
not work correctly.
Refer to 6th item of Error U23.
Three sensor model(S8127/S8120)
ST4 0 : center, 1 : left, 2 : right
ST4 0 : center, 1 : left, 2 : right
Five sensor model(S8147/S8150/S8130)
ST4 0 : center, 1 : R1, 2 : L1, 3 : R2, 4 : L2
ST4 0 : center, 1 : R1, 2 : L1, 3 : R2, 4 : L2
F90
(Sub-Processor Error)
(Sub-Processor Error)
9E
x
x
x
Sub-processor error of ASIC
(IC1/IC2)
(IC1/IC2)
1. Check the soldering condition of CONTROL
Board and its surrounding parts.
ASIC(ST3 0 : IC1, 1 : IC2)
ASIC(ST3 0 : IC1, 1 : IC2)
2. Replace faulty parts or board.
Error Code
ST1 ST2 ST3 ST4
Possible Cause
Recommended action
Remarks
Figure 1
Figure 2
Click on the first or last page to see other KV-S8147-M / KV-S8127-M / KV-S8150 / KV-S8130 / KV-S8120 service manuals if exist.