Read Panasonic KV-S7097 / KV-S7077 Service Manual online
112
4. Carriage Home Detector does
not work correctly.
1. Check the alignment of the Carriage Home
Detector and its actuator is proper.
2. Execute “Key / Sensor” test in Sec.9.3.7 to
check the sensor condition.
3. Check the following connection and solder-
ing condition of each connector.
a. CN10 (CARRIAGE HOME DETECTOR
a. CN10 (CARRIAGE HOME DETECTOR
Board) to CN513 (MAIN Board)
4. Check the soldering condition of IC3 and its
surrounding circuit on the CARRIAGE
HOME DETECTOR Board to repair it.
HOME DETECTOR Board to repair it.
5. Check the following signals.
CRHOME signal (CN10-1st pin on the CAR-
RIAGE HOME DETECTOR Board, IC524-
A11 pin on the MAIN Board): Approx. 3 V
(when the actuator interrupts the detector)
RIAGE HOME DETECTOR Board, IC524-
A11 pin on the MAIN Board): Approx. 3 V
(when the actuator interrupts the detector)
6. Replace faulty parts or boards.
F60 (Front-side gain
adjustment error)
adjustment error)
50
00
00
00 1. Scanning Glass (F) is dirty.
Clean the glass surface in the Sec. 7.2.4.
2. CIS Unit (F) does not work prop-
erly.
1. Check if the White Standard Sheet is not
dirty and not peeled, then is stuck properly.
2. Execute Focus test in the Sec.9.3.7. to check
the peak level.
3. Check that LED (F) lights during Focus test.
4. Execute Shading adjust in the Sec.9.3.8. to
4. Execute Shading adjust in the Sec.9.3.8. to
adjust the shading correction level.
5. Check the following connections and solder-
ing condition on each connector.
a. CIS Unit (F) to CN100 (CIS (F) RELAY
Board)
b. CN103, CN104 (CIS (F) RELAY Board) to
CN502, CN503 (MAIN)
c. CIS Unit (F) to CN101, CN102 (CIS (F)
RELAY Board)
6. Check the power supply for LED.
CN502-7, 8th pin (MAIN Board) : 12 V.
7. Replace faulty parts or boards.
3. Pixel data from CIS Unit (F) or
image processing circuit has
some problems.
some problems.
1. Check the following connections and solder-
ing condition on each connector.
a. CIS Unit (F) to CN100 (CIS (F) RELAY
Board)
b. CN103, CN104 (CIS (F) RELAY Board) to
CN502, CN503 (MAIN Board)
2. Check the following power supply to MAIN
Board.
CN502-9, 10 pin (MAIN Board) : 5.0 V
CN502-9, 10 pin (MAIN Board) : 5.0 V
3. Check the soldering condition of the
CN4,IC16, and their surrounding circuit on
the MAIN Board.
the MAIN Board.
4. Replace faulty parts or boards.
F61 (Front-side
black level error)
black level error)
51
00
00
00 1. Pixel data from Optical Unit
Front or image processing
circuit has some problems.
circuit has some problems.
1.Check if the White Standard Sheet is not dirty
and not peeled, then is stuck properly.
2.Refer to the above 3rd item on the F60.
and not peeled, then is stuck properly.
2.Refer to the above 3rd item on the F60.
F62 (Back-side gain
adjustment error)
adjustment error)
52
00
00
00 1. Scanning Glass (B) is dirty.
Clean the glass surface in the Sec. 4.2.4.
Error Code
ST1 ST2 ST3 ST4
Possible Cause
Check Point
Remarks
Click on the first or last page to see other KV-S7097 / KV-S7077 service manuals if exist.