Read Panasonic KV-S3065CL / KV-S3065CW (serv.man4) Service Manual online
Error Code
Possible Cause
Check Point
Remarks
Classified Code
ST1
ST2
ST3
ST4
U14
(Conveyor Jam 3)
: Paper did not
reach the Ending
(Front) Sensor.)
(Conveyor Jam 3)
: Paper did not
reach the Ending
(Front) Sensor.)
14
00
00
00
1. Document remains between
Paper Jam Sensor and Ending
(Front) Sensor.
Paper Jam Sensor and Ending
(Front) Sensor.
Remove the document from the scanner.
2. Paper dust exists on or around
the Ending (Front) Sensor.
the Ending (Front) Sensor.
1.
Blow off the dirt with the accessory
blower. (See Sec.7.)
blower. (See Sec.7.)
2.
Execute Key / Sensor and Sensor
Sensitive Level tests in Sec.9.3.6 to
check the sensor condition.
Sensitive Level tests in Sec.9.3.6 to
check the sensor condition.
3. Ending (Front) Sensor does not
work, correctly.
work, correctly.
1.
Execute Key / Sensor and Sensor
Sensitive Level tests in Sec.9.3.6 to
check the sensor condition.
Sensitive Level tests in Sec.9.3.6 to
check the sensor condition.
2.
Check whether the sensor alignment is
proper (whether the sensor direction faces
to its reflector.)
proper (whether the sensor direction faces
to its reflector.)
3.
Check the following connection and
soldering condition on each connector.
soldering condition on each connector.
a.
CN5024 (ENDING (FRONT) SENSOR
Board) to CN5023 (RELAY (UPPER)
Board)
Board) to CN5023 (RELAY (UPPER)
Board)
b.
CN5022 (RELAY (UPPER) Board) to
CN1014 (CONTROL Board)
CN1014 (CONTROL Board)
4.
Check the following signals.
a.
F_ENDING signal (CN5024-3
rd
pin,
CN5023-3
rd
pin, CN5022-2
nd
pin,
CN1014-2
nd
pin)
→ 0 V (when none exists on the
Ending (Front) Sensor)
Ending (Front) Sensor)
b.
Check the reference signals for the
PEXIT signal on the CONTROL
Board.
PEXIT signal on the CONTROL
Board.
→ IC1015-6
th
pin: 1.5 V or less
(After initializing)
→ IC1017-7
th
pin: Approx. 1.5 V
c.
Check comparator output signal.
→ IC1017-1
st
pin: 3.3 V
(When no paper exists)
5.
Replace faulty parts or board.
4. Mechanical problem (Drive Roller,
Drive Belt, Conveyor)
Drive Belt, Conveyor)
1.
Execute Conveyor Motor test in
Sec.9.3.6 to check the mechanical
condition.
Sec.9.3.6 to check the mechanical
condition.
2.
Check whether the Conveyor Rollers
(2, 3) and Drive belt, and whether the
conveyor to support the Drive Rollers are
put together into the scanner, properly.
(2, 3) and Drive belt, and whether the
conveyor to support the Drive Rollers are
put together into the scanner, properly.
3.
Check the surfaces of the Conveyor
Rollers (2, 3).
Rollers (2, 3).
a.
Configuration:
Do the rollers swell irregularly?
→ Replace the rollers.
b.
Whether the roller surfaces are dirty
→ Clean the surfaces.
4.
Check whether the Drive Belt tension is
proper.
proper.
→ Re-adjust the belt tension.
105
KV-S3065CLSERIES / KV-S3065CWSERIES
Click on the first or last page to see other KV-S3065CL / KV-S3065CW (serv.man4) service manuals if exist.