Read Panasonic VDR-D100EB / VDR-D100EG / VDR-D150E / VDR-D150EB / VDR-D150EE / VDR-D150EF / VDR-D150EG / VDR-D150EP / VDR-D150GC / VDR-D150GCS / VDR-D150GN / VDR-D150SG / VDR-D152EG / VDR-D158GK Service Manual online
VDR-D100EB VDR-D100EG
VDR-D150E VDR-D150EB
VDR-D150EE VDR-D150EF
VDR-D150EG VDR-D150EP
VDR-D150GC VDR-D150GCS
VDR-D150GN VDR-D150SG
VDR-D152EG VDR-D158GK
VDR-D150EE VDR-D150EF
VDR-D150EG VDR-D150EP
VDR-D150GC VDR-D150GCS
VDR-D150GN VDR-D150SG
VDR-D152EG VDR-D158GK
Vol. 1
Colours
(S)...................Silver Type
Digital Video Camcorder
ORDER NO. VM0602006CE
1
Safety Precautions
3
1.1.
General Guidelines
3
2
Warning
4
2.1.
Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
4
2.2.
Caution for AC Cord (VJA0940 type)
5
2.3.
How to Replace the Lithium Battery
6
3
Service Navigation
7
3.1.
Introduction
7
3.2.
About Lead Free Solder (PbF)
7
4
Specifications
8
5
Location of Controls and Components
9
6
Service Mode
21
6.1.
Error Display
21
6.2.
Service Menu
21
7
Service Fixture & Tools
23
7.1.
Service Fixture and Tools
23
7.2.
Service Position
24
7.3.
Removal/Installation of F.P.C. From Non ZIF (Zero
Insertion Force) Connector
26
7.4.
Method for Ejecting the DVD Tray Manually
27
7.5.
EEPROM Data
27
7.6.
Special Note
28
7.7.
IC6001 REPLACEMENT NOTE
28
8
Disassembly and Assembly Instructions
29
8.1.
Cabinet Section
29
9
Measurements and Adjustments
47
9.1.
Electrical Adustment
47
10 Maintenance
49
10.1. Cleaning Lens, Viewfinder and LCD Panel
49
10.2. Cleaning disc and optical pickup
49
11 Block Diagrams
51
12 Schematic Diagrams
61
12.1. SCHEMATIC DIAGRAM & CIRCUIT BOARD LAYOUT
NOTES
61
12.2. FRONT SCHEMATIC DIAGRAM
62
12.3. SIDE R SCHEMATIC DIAGRAM
63
12.4. LCD BACKLIGHT SCHEMATIC DIAGRAM
64
12.5. JACK / EVF BACKLIGHT / DISK COVER LOCK
SCHEMATIC DIAGRAMS
65
12.6. CCD / LCD SW / SIDE L/DISK SCHEMATIC DIAGRAMS
66
12.7. INTERCONNECTION SCHEMATIC DIAGRAM
67
12.8. VOLTAGE CHART
68
13 Printed Circuit Board
69
13.1. FRONT P.C.B.
69
13.2. JACK P.C.B.
70
13.3. LCD BACKLIGHT P.C.B.
71
13.4. SIDE R P.C.B. / OPEN SWITCH P.C.B.
72
14 Exploded View
73
14.1. MAIN PARTS SECTION
73
14.2. FRONT CASE, MAIN P.C.B. AND JACK P.C.B. SECTION
74
14.3. SIDE CASE R AND LCD SECTION
75
14.4. CCD AND LENS SECTION
76
14.5. REAR CASE AND EVF SECTION
77
14.6. PACKING PARTS AND ACCESSORIES SECTION
78
15 Replacement Parts Lists
79
15.1. MECHANICAL REPLACEMENT PARTS LIST
79
15.2. ELECTRICAL REPLACEMENT PARTS LIST
81
CONTENTS
Page
Page
2
1 Safety Precautions
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These parts are marked by
which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essential
that
that
these
critical
parts
should
be
replaced
with
manufacturer’s specified parts to prevent shock, fire, or
other hazards. Do not modify the original design without
permission of manufacturer.
other hazards. Do not modify the original design without
permission of manufacturer.
2. An Isolation Transformer should always be used during the
servicing of AC Adaptor whose chassis is not isolated from
the AC power line. Use a transformer of adequate power
rating as this protects the technician from accidents
resulting in personal injury from electrical shocks. It will also
protect AC Adaptor from being damaged by accidental
shorting that may occur during servicing.
the AC power line. Use a transformer of adequate power
rating as this protects the technician from accidents
resulting in personal injury from electrical shocks. It will also
protect AC Adaptor from being damaged by accidental
shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been
overheated or damaged by the short circuit.
overheated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices such
as insulation barriers, insulation papers shields are properly
installed.
installed.
5. After servicing, make the following leakage current checks
to prevent the customer from being exposed to shock
hazards.
hazards.
3
2 Warning
2.1. Prevention of Electro Static Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable
conductive material).
conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)
sufficient to damage an ES device).
sufficient to damage an ES device).
4