HDC-SD200EB, HDC-SD200EC, HDC-SD200EF, HDC-SD200EG, HDC-SD200EP, HDC-TM200EE, HDC-TM200GC, HDC-TM200GD, HDC-TM200GJ, HDC-TM200GK, HDC-TM200GN, HDC-TM200GT, HDC-TM200SG, HDC-TM200EEK - Panasonic Movie Service Manual (repair manual)

hdc-sd200eb, hdc-sd200ec, hdc-sd200ef, hdc-sd200eg, hdc-sd200ep, hdc-tm200ee, hdc-tm200gc, hdc-tm200gd, hdc-tm200gj, hdc-tm200gk, hdc-tm200gn, hdc-tm200gt, hdc-tm200sg, hdc-tm200eek service manual
Model
HDC-SD200EB HDC-SD200EC HDC-SD200EF HDC-SD200EG HDC-SD200EP HDC-TM200EE HDC-TM200GC HDC-TM200GD HDC-TM200GJ HDC-TM200GK HDC-TM200GN HDC-TM200GT HDC-TM200SG HDC-TM200EEK
Pages
86
Size
6.38 MB
Type
PDF
Document
Service Manual
Brand
Device
Movie / HIGH DEFINITION VIDEO CAMERA
File
hdc-sd200eb-hdc-sd200ec-hdc-sd200ef-hdc-sd200eg-hd.pdf
Date

Read Panasonic HDC-SD200EB / HDC-SD200EC / HDC-SD200EF / HDC-SD200EG / HDC-SD200EP / HDC-TM200EE / HDC-TM200GC / HDC-TM200GD / HDC-TM200GJ / HDC-TM200GK / HDC-TM200GN / HDC-TM200GT / HDC-TM200SG / HDC-TM200EEK Service Manual online

ORDER NO. VM0902003CE
B27
High Definition Video Camera
Model No.
HDC-SD200EB
       HDC-SD200EC
       HDC-SD200EF
       HDC-SD200EG
       HDC-SD200EP
       HDC-TM200EE
       HDC-TM200GC
       HDC-TM200GD
       HDC-TM200GJ
       HDC-TM200GK
       HDC-TM200GN
       HDC-TM200GT
       HDC-TM200SG
Vol. 1
Colour
(K)...........Black Type
(S)...........Silver Type
(only HDC-SD200EG/HDC-TM200GC)
4
2
TABLE OF CONTENTS
PAGE
PAGE
1 Safety Precaution -------------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.) --------3
1.4. How to Discharge the Capacitor on Sub PCB ------4
2 Warning --------------------------------------------------------------5
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------5
2.2. How to Recycle the Lithium Ion Battery (U.S.
Only)-----------------------------------------------------------5
2.3. Caution for AC Cord (For EB/GC/SG) ----------------6
2.4. How to Replace the Lithium Battery -------------------7
3 Service Navigation------------------------------------------------8
3.1. Introduction --------------------------------------------------8
3.2. General Description About Lead Free Solder
(PbF) ----------------------------------------------------------8
3.3. Important Notice 1 -----------------------------------------8
3.4. How to Define the Model Suffix (NTSC or PAL
model)---------------------------------------------------------9
3.5. Formatting Buit-in Memory (HDC-TM200 only)--- 10
4 Specifications ---------------------------------------------------- 11
5 Location of Controls and Components------------------ 14
6 Service Mode ----------------------------------------------------- 20
6.1. Built-in Memory Self Check (HDC-TM200
only) --------------------------------------------------------- 21
6.2. Lock Search History Indication ----------------------- 22
6.3. Power ON Self Check Result Display--------------- 23
7 Disassembly and Assembly Instructions--------------- 24
7.1. Disassembly Flow Chart-------------------------------- 24
7.2. PCB Location---------------------------------------------- 24
7.3. Disassembly Procedure -------------------------------- 25
8 Measurements and Adjustments -------------------------- 42
8.1. Electric Adjustment -------------------------------------- 42
9 Factory Setting--------------------------------------------------- 44
9.1. HOW TO TURN ON THE FACTORY
SETTINGS? ----------------------------------------------- 44
9.2. WHAT IS THE FACTORY SETTINGS? ------------ 44
3
1 Safety Precaution
1.1.
General Guidelines
1.
IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essen-
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
2. An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been over-
heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2.
Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 M
Ω and 5.2 MΩ. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
1.3.
Leakage Current Hot Check
(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5 k
Ω, 10 W resistor, in parallel with a 0.15 μF
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 k
Ω/V or more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the volt-
age at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equiva-
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Figure. 1
4
1.4.
How to Discharge the Capacitor on Sub PCB
CAUTION:
1.
Be sure to discharge the capacitor on SUB PCB.
2.
Be careful of the high voltage circuit on SUB PCB when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and Remove the necessary parts/unit.
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k
Ω /5W).
(an equivalent type of resistor may be used.)
3. Put the resistor between both terminals of capacitor on SUB PCB for approx. 5 seconds.
4. After discharging confirm that the capacitor voltage is lower than 10V using a voltmeter.
Fig. F1
Page of 86
Display

Download Panasonic HDC-SD200EB / HDC-SD200EC / HDC-SD200EF / HDC-SD200EG / HDC-SD200EP / HDC-TM200EE / HDC-TM200GC / HDC-TM200GD / HDC-TM200GJ / HDC-TM200GK / HDC-TM200GN / HDC-TM200GT / HDC-TM200SG / HDC-TM200EEK Service Manual (Repair Manual)

Here you can read online and download Panasonic HDC-SD200EB / HDC-SD200EC / HDC-SD200EF / HDC-SD200EG / HDC-SD200EP / HDC-TM200EE / HDC-TM200GC / HDC-TM200GD / HDC-TM200GJ / HDC-TM200GK / HDC-TM200GN / HDC-TM200GT / HDC-TM200SG / HDC-TM200EEK Service Manual in PDF. HDC-SD200EB / HDC-SD200EC / HDC-SD200EF / HDC-SD200EG / HDC-SD200EP / HDC-TM200EE / HDC-TM200GC / HDC-TM200GD / HDC-TM200GJ / HDC-TM200GK / HDC-TM200GN / HDC-TM200GT / HDC-TM200SG / HDC-TM200EEK service manual will guide through the process and help you recover, restore, fix, disassemble and repair Panasonic HDC-SD200EB / HDC-SD200EC / HDC-SD200EF / HDC-SD200EG / HDC-SD200EP / HDC-TM200EE / HDC-TM200GC / HDC-TM200GD / HDC-TM200GJ / HDC-TM200GK / HDC-TM200GN / HDC-TM200GT / HDC-TM200SG / HDC-TM200EEK Movie. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.