Read Panasonic EH-NE64-K865 Service Manual online
Order Number PEWT1610A21CE
(Household) Hair Dryer
Model No.
EH-NE64
Asia
CIS
Middle East
CIS
Middle East
TABLE OF CONTENTS
PAGE
1 Warning --------------------------------------------------------------------------------------------
2
2 Specifications -------------------------------------------------------------------
2
3 Troubleshooting Guide ------------------------------------------------------------
3
4 Disassembly and Assembly Instructions ----------------------------
4
4.1 Disassembly instruction-----------------------------------------------
4
4.2 Assembly Instructions----------------------------------------------------------
5
5 Wiring Connection Diagram--------------------------------------------
6
6 Schematic Diagram -----------------------------------------------------------
7
7 Exploded View & Replacement Parts List ------------------------------------
8
7.1 Exploded View for EH-NE64 ------------------------------------------------
8
7.2 Parts List for EH-NE64 --------------------------------------------------------------
9
1. Warning
Caution:
- Pb free solder has a higher melting point that standard solder; Typicall the melting point is 50 - 70°F (30 - 40
℃) higher.
Please use a oldering iron with temperature control and adjust it to 750 ±20°F (400 ± 10
℃).
In case of using high temperature soldering iron, please becareful not to heat too long.
- Pb free solder will tend to splash when heated too high (about 1100°F / 600
℃).
Power source
AC 220-240 V 50-60 Hz
Power consumption
Approx. "3" Turbo
220 V ~ 1700 W
230 V ~ 1850 W
240 V ~ 2000 W
Air volume without nozzle
1.45 m3/min
Air flow temperature ("3" Turbo)
90 K (in case of room temperature 30°C)
Dimensions
(W) 80 x (D) 170 x (H) 260 mm
Cord length
L = 1.7 m
Weight
Approx. 380 g ( Without cord and Without Nozzle )
Supplied accessory
EH-NE64
Set nozzle
2. Specifications
3 TROUBLESHOOTING GUIDE
Refer to WIRING CONNECTION DIAGRAM.
< TROUBLE >
< CHECK >
< REMEDY >
Main Body does not
operate
<CHECK POWER CORD>
Check the conductivity of POWER CORD.
<CHECK MAIN SWITCH>
Check the conductivity between the terminal 1
and 4 by setting the main switch at Position 1.
(Figure 1)
Replace the MAIN
SWITCH
Replace the MOTOR
HEATER ASSEMBLY
NG
Figure 1
OK
NG
OK
Hot Air is not emitted
<CHECK MAIN SWITCH>
Check the conductivity between the terminal 2
and 4 by setting the main switch at Position 2
(Figure 2)
Replace the MAIN
SWITCH
NG
OK
Figure 2
<CHECK HEATER BLOCK>
Check if there are foreign objects on the joint
of the thermo switch (Figure 3)
Remove the foreign
objects on the joints
OK
NG
Replace the MOTOR
HEATER ASSEMBLY
Replace the MOTOR
HEATER ASSEMBLY
Thermo switch
Lead Wire ( Violet
)
Lead Wire ( Brown)
Lead Wire ( White)
Lead Wire ( Green
)
Lead Wire ( Brown-Cod)
Lead Wire ( Violet)
Lead Wire ( Brown)
Lead Wire ( White)
Lead Wire ( Green)
Lead Wire ( Brown-Cod)
Figure 2
Lead Wire ( Black)
Lead Wire ( Black)
4. Disassembly and Assembly Instructions
4.1. Disassembly Instructions
(1) Take
off NOZZLE as same direction as below.
(4). Take off HANDLE AB then take out
CLICK RING and SWIVEL RING
method as below.
CLICK RING and SWIVEL RING
method as below.
(2). Remove 2 TAPPING SCREWS at HOUSING A
(5). Take off HOUSING A method as below.
by flat-blade screwdriver and 2 TORX SCREWS
at HANDLE by Driver.
at HANDLE by Driver.
(3) Take off an AIR OUTLET GRILL and an AIR OUTLET RING
(6). Take off a
by rotating method as below.
MOTOR HEATER BLOCK ASS'Y
method as below.
method as below.
Counter clockwise
Torx screws
Tapping screws