Read Panasonic EH-HV20-K865 Service Manual online
Order Number PEWT1511A86CE
(Household) Straight & Curl Straightener
Model No. EH-HV20
Asia
CIS
Middle East
TABLE OF CONTENTS
Page
1 Warning ---------------------------------------------------------------------------
1
2 Specifications ----------------------------------------------------------------
1
3 Troubleshooting Guide ----------------------------------------------------
2
4 Disassembly and Assembly Instructions --------------------------
4
5 Wiring Connection Diagram----------------------------------------------
9
6 Schematic Diagram --------------------------------------------------------
9
7 Exploded View & Replacement Parts List -------------------------
10
1. Warning
Caution:
- Pb free solder has a higher melting point that standard solder Typicall the melting point is 50 - 70°F (30 - 40
℃
)
a higher. Please use soldering iron with temperature control and adjust it to 750 ±20°F (400 ± 10
℃
).
In case of using high temperature soldering iron, please be careful not to heat too long.
- Pb free solder will tend to splash when heated too high (about 1100°F / 600
℃
).
Model
Sales Area
Power source / Power consumption
Iron Plate temperature
Body size (mm.)
Weight
Cord length
415 g
365 g
355 g
Asia / CIS / Middle East
180-200-230°C (3 level settings)
290×33×33
AC 220-240V ~ 50-60Hz 55W
EH-HV20
2. Specifications
AC 100-130V ~ 50-60Hz 51W
355 g
S3 Plug(SF629)
B2 Plug(SF82)
B2 Plug (SF822)
A2 Plug (LM-201-9)
2.0 m
B2(SF822) Plug
B2(SF82) Plug
2.0 m
2.0 m
S3(SF629) Plug
A2(LM-201-9) Plug
2.0 m
3. TROUBLESHOOTING GUIDE
Refer to WIRING CONNECTION DIAGRAM.
No operation
(LED does not light)
< CHECKING PROCEDURE >
< CHECKING METHOD >
< REMEDY >
Check Power cord.
Check the conductivity
of power cord.
Check Circuit assembly b/k
LED light, but Iron
Plate(Heater)
does not become hot
Check Iron plate of Heater
A : Housing side
Replace Heater A ass'y b/k
Check resistance value between lead
wires of the Housing side assy is
approx. 20.0±1.0
Ω
Check the Lead Wire
Check connecting of Lead Wire
Replace Heater A ass'y b/k
or Heater B ass'y b/k
Replace Heater B ass'y b/k
OK
Check Power Switch
Check continuous at Switch ON
position
Replace the Power Cord
Check Iron plate of Heater
B : Press plate side
Check resistance value between lead
wires of the Press plate side assy is
approx. 20.0±1.0
Ω
Check Circuit assembly b/k
Replace Circuit assembly b/k
Replace Power switch
Replace Ciruit assembly b/k
OK
NG
NG
NG
NG
NG
NG
OK
NG
OK
4 Disassembly and Assembly instructions
4.1 Disassembly instruction
(1) Remove Hinge Cover from Main Body
(4) Remove 3 screws for fitting Press Plate side
by Slotted screw driver (Minus Driver.)
by Phillips screw drivers (Plus Driver).
(2) Remove Hinge Pin by hand pressing at
(5) Remove Press Plate Cover from Press Plate
Housing side and Press Plate side.
in Grip follow as below drawing.
(3) Remove Pivot spring by gripping
(6) Take off Iron Plate from Press Plate.
and pulling it out from the Main body
Hinge Cover
Minus Driver
Housing
Press Plate
Hinge Pin
Pivot Spring
Screws
Press Plate Cover
Press Plate