Read Panasonic EH-HV11-K865 Service Manual online
ORDER NO. PEWT1908A42CE
(Household) Straight & Curl Straightener
Model No.
EH-HV11
Asia & CIS
TABLE OF CONTENTS
PAGE
1 Warning ---------------------------------------------------------------------------
2
2 Specifications ----------------------------------------------------------------
2
3 Troubleshooting Guide ----------------------------------------------------
3
4 Disassembly and Assembly Instructions --------------------------
4
4.1 Disassembly Instructions---------------------------------
4-5
4.2 Assembly Instructions--------------------------------------
6
5 Wiring Connection Diagram----------------------------------------------
7
6 Schematic Diagram --------------------------------------------------------
8
7 Exploded View & Replacement Parts List -------------------------
9
7.1 EH-HV11 Exploded View-------------------------------------------------
9
7.2 EH-HV11 Replacement Parts List-------------------------------------
10
1. Warning
Caution:
- Pb free solder has a higher melting point that standard solder Typicall the melting point is 50 - 70°F (30 - 40
℃)
a higher. Please use soldering iron with temperature control and adjust it to 750 ±20°F (400 ± 10℃).
In case of using high temperature soldering iron, please be careful not to heat too long.
- Pb free solder will tend to splash when heated too high (about 1100°F / 600
℃).
Power source
Power consumption
Iron Plate temperature
Body size (mm.)
Weight
Cord length
Without Cap
300 g
With Cap
S3 Plug
(UK13A3)
330 g
B2 Plug
(SF822)
With Cap
290 g
Without Cap
260 g
B2(SF822) Plug
1.7 m
B2(M3204) Plug
1.7 m
S3(UK13A3) Plug
1.7 m
Without Cap
300 g
With Cap
B2 Plug
(M3204)
270 g
Without Cap
With Cap
235 x 35 x 39
230 x 28 x 32
2. Specifications
AC 100-240 V, 50-60 Hz
22 W
200 °C
3. Troubleshooting Guide
(Refer to SCHEMATIC DIAGRAM)
Check resistance of IRON PLATE
( 200-800 Ω)
<CHECK>
<REMEDY>
Check continuous at Switch ON position (Figure 2)
Check continuous of Current Fuse
of IRON PLATE ASSEMBLY (Figure 3)
<TROUBLE>
Check continuous of POWER CORD (Figure 1)
Iron plate no hot
Check POWER CORD
Change POWER CORD
Change IRON PLATE
Check power switch
Check IRON PLATE
Change Power Switch
Change IRON PLATE
OK
(Figure 1)
No
No
Tester
OK
No
(Figure 2)
OK
No
Tester
(Figure 3)
Tester
Tester
4. Disassembly and Assembly Instructions
4.1 Disassembly Instructions
1. Insert a small flat head screwdriver
3. Remove the spring by pull out the HOUSING side
into the groove of the SHAFT COVER
and PRESS PLATE side as shown in Figure 6.
as shown in Figure 4.
(Figure 6)
4. Using a screwdriver remove the 2 TAPPING
SCREWS from PRESS PLAVE COVER as shown
in Figure 7.※Be careful not to lose the spring ※.
SCREWS from PRESS PLAVE COVER as shown
in Figure 7.※Be careful not to lose the spring ※.
(Figure 4)
(Figure 7)
2. Remove the SHAFT SCREW and take off
5.Take off the PRESS PLATE COVER
the SHAFT from Main body as shown in Figure 5.
as shown in Figure 8.
(Figure 5)
(Figure 8)
Shaft Cover
groove of Shaft Cover
groove of Shaft Cover
Shaft
Shaft screw
Spring
Pul
l
Pull
Tapping screws
Spring
Press plate Cover