Read Panasonic EH-HS41-K865 (serv.man4) Service Manual online
Order Number PEWT1512A04CE
(Household) Hair Straightener
Model No. EH-HS41
CIS
Middle East
Asia
TABLE OF CONTENTS
Page
1 Warning…………………………………………………1
2 Specifications…………………………………………1
3 Troubleshooting Guide………………………………2
4 Disassembly and Assembly instructions…………4
5 Wiring Connection Diagram…………………………
2 Specifications…………………………………………1
3 Troubleshooting Guide………………………………2
4 Disassembly and Assembly instructions…………4
5 Wiring Connection Diagram…………………………
9
6 Schematic Diagram……………………………………
9
7 Explode View and Replacement Part List……… 10
1. Warning
Caution:
- Pb free solder has a higher melting point that standard solder Typical the melting point is 50 - 70°F (30 - 40℃)
a higher. Please use soldering iron with temperature control and adjust it to 750 ±20°F (400 ± 10℃).
In case of using high temperature soldering iron, please be careful not to heat too long.
- Pb free solder will tend to splash when heated too high (about 1100°F / 600℃).
Model
Sales Area
Power source / Power consumption
Iron Plate temperature
Body size (mm.)
Weight
Cord length
2.0 m
2.0 m
2.0 m
S3(SF629) Plug
B2(SF822) Plug
B2(SF82) Plug
AC 100-130V ~ 50-60Hz 55W
EH-HS41
Asia
AC 220-240V ~ 50-60Hz 55W
B2 Plug(SF82)
B2 Plug (SF822)
2. Specifications
435 g
378 g
380 g
140-160-180-200-230℃ (5 level settings)
287×42×45
S3 Plug(SF629)
3. TROUBLESHOOTING GUIDE
Refer to WIRING CONNECTION DIAGRAM.
LED at 140 º C
No operation
(LED does not light)
< CHECKING PROCEDURE >
< CHECKING METHOD >
< REMEDY >
Check the Power cord.
Check the conductivity
of Power cord.
Check the Power Switch
(0/1)
Hold the On/off switch (Tag Switch)
pressed longer and check if LED
(Power Lamp) lights. LED at * 140ºC
will start blinking (LED will turn from
BLINK to LIGHT after round one
minute).
LED light, but Iron
Plate(Heater)
does not become hot
Check Iron plate of Heater
A : Housing side
Replace Heater A ass'y b/k
Check if resistance value between
lead wires of the Housing side assy is
approx. 20.0±1.0
Check the Lead Wire
Check connecting of Lead Wire
Replace Heater A ass'y b/k
or Heater B ass'y b/k
Replace Heater B ass'y b/k
O
Check Circuit assembly b/k
Replace Circuit assembly
b/k
b/k
LED dose not light , Iron
Plate(Heater A,B)
Replace Circuit assembly
b/k
b/k
Check the Power Switch
button of the Housing side
Check the operation of On/off Switch
button of Housing side.
(Check if it works smoothly)
Replace the Power Cord
Figure1
Check Iron plate of Heater
B : Press plate side
Check if resistance value between
lead wires of the Press plate side
assy is approx. 20.0±1.0
Replace the Housing A
Replace Circuit assembly
b/k
O
N
N
N
O
O
N
N
N
N
N
O
O
Temperature dose not
change even though the
Temperature level
adjustment switches
is pressed.
Check the Temperature
level Adjustment Switch
(Tag Switch)
Check Circuit assembly b/k
Replace Circuit assembly
b/k
b/k
< CHECKING PROCEDURE >
< CHECKING METHOD >
< REMEDY >
Check Circuit assembly b/k
Replace Circuit assembly
b/k
Figure2
O
All LEDs blinks.
Check Heater A
: Housing side
Check connecting of Thermistor
Replace Heater A :
Housing side
N
LED lights, but the Iron
plate (Heater A,B) dose
plate (Heater A,B) dose
not become hot.
N
Check the operation of LED(Temp.
Level Lamp) by pressing Tag switch
of the Temperature level adjustment
of the Temperature level adjustment
switch on Circuit assembly b/k longer
with fingers (Figure2)
N
Replace Circuit assembly
b/k
N