DVD-S68EE, DVD-S48EE - Panasonic DVD Service Manual (repair manual)

dvd-s68ee, dvd-s48ee service manual
Model
DVD-S68EE DVD-S48EE
Pages
28
Size
2.02 MB
Type
PDF
Document
Service Manual
Brand
Device
DVD / DVD/CD PLAYER
File
dvd-s68ee-dvd-s48ee.pdf
Date

Read Panasonic DVD-S68EE / DVD-S48EE Service Manual online

ORDER NO. DSD1102002CE
DVD/CD Player
Model No.
DVD-S68EB
DVD-S68EE
DVD-S68EG
DVD-S68EP
DVD-S48EB
DVD-S48EE
DVD-S48EG
DVD-S48EP
Colour
(K)...........Black Type
4
2
TABLE OF CONTENTS
PAGE
PAGE
1 Safety Precautions -----------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.) --------3
2 Warning --------------------------------------------------------------4
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------4
2.2. Caution for AC Cord (For the United Kingdom
and Republic of Ireland) ----------------------------------5
2.3. Precaution of Laser Diode -------------------------------6
2.4. Static Electricity Protection Measures ----------------7
2.5. Ground for electrostatic breakdown
prevention ----------------------------------------------------7
3 Service Navigation------------------------------------------------8
3.1. Service Infomation -----------------------------------------8
3.2. How to Checking Recognition of USB Device ------8
3.3. How to Update Firmware---------------------------------9
3.4. Caution for DivX ------------------------------------------ 10
4 Specifications ---------------------------------------------------- 11
4.1. Others (Licenses) ---------------------------------------- 12
5 Location of Controls and Components------------------ 13
6 Operating Instructions ---------------------------------------- 14
6.1. Taking out the Disc from Drive Unit when the
Disc cannot be ejected by OPEN/CLOSE
button-------------------------------------------------------- 14
7 Troubleshooting Guide---------------------------------------- 15
7.1. About Operation of Set --------------------------------- 15
7.2. About Citcuit ----------------------------------------------- 16
8 Wiring Connection and Voltage Data --------------------- 18
8.1. DVD-S48 --------------------------------------------------- 18
8.2. DVD-S68 --------------------------------------------------- 19
9 Disassembly and Assembly Instructions --------------- 20
9.1. Unit (DVD-S48) ------------------------------------------- 20
9.2. Unit (DVD-S68) ------------------------------------------- 23
10 Exploded View and Replacement Parts List ----------- 26
10.1. Casing Parts & Mechanism Section ----------------- 26
10.2. Packing & Accessories Section ---------------------- 27
10.3. Replacement Parts List --------------------------------- 28
3
1 Safety Precautions
1.1.
General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essen-
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
2. An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been over-
heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2.
Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 M
Ω and 5.2 MΩ. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
1.3.
Leakage Current Hot Check
(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5 k
Ω, 10 W resistor, in parallel with a 0.15 μF
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 k
Ω/V or more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the volt-
age at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equiva-
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Figure. 1
4
2 Warning
2.1.
Prevention of Electrostatic Discharge (ESD) to Electrostatically 
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge
(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).
Page of 28
Display

Download Panasonic DVD-S68EE / DVD-S48EE Service Manual (Repair Manual)

Here you can read online and download Panasonic DVD-S68EE / DVD-S48EE Service Manual in PDF. DVD-S68EE / DVD-S48EE service manual will guide through the process and help you recover, restore, fix, disassemble and repair Panasonic DVD-S68EE / DVD-S48EE DVD. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.