Read Panasonic DMC-ZX1EB / DMC-ZX1EE / DMC-ZX1EF / DMC-ZX1EG / DMC-ZX1EP / DMC-ZX1SG / DMC-ZR1P / DMC-ZR1PC / DMC-ZR1PR / DMC-ZR1PU / DMC-ZR1GC / DMC-ZR1GD / DMC-ZR1GH / DMC-ZR1GK / DMC-ZR1GN / DMC-ZR1GT Service Manual online
DMC-ZX1EE
DMC-ZX1EF
DMC-ZX1EG
DMC-ZX1EP
DMC-ZX1SG
DMC-ZR1P
DMC-ZR1PC
DMC-ZR1PR
DMC-ZR1PU
DMC-ZR1GC
DMC-ZR1GD
DMC-ZR1GH
DMC-ZR1GK
DMC-ZR1GN
DMC-ZR1GT
(S)...........Silver Type (except PR/EF/GD/GT)
(K)...........Black Type
(A)...........Blue Type (only P/PC/EB/EF/EG/EP/GN)
(R)...........Red Type (except PR/EE/GD/GK)
(W)..........White Type
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.) --------3
1.4. How to Discharge the Capacitor on
2.4. How to Replace the Lithium Battery -------------------7
3.2. General Description About Lead Free Solder
5 Location of Controls and Components------------------ 14
6 Service Mode ----------------------------------------------------- 16
6.2. ICS (Indication of additional Camera Settings
7.2. When Replacing the Main P.C.B. -------------------- 21
7.3. Service Position ------------------------------------------ 21
8.2. P.C.B. Location ------------------------------------------- 22
8.3. Disassembly Procedure -------------------------------- 23
8.4. Disassembly Procedure for the Lens --------------- 30
8.5. Assembly Procedure for the Lens ------------------- 34
8.6. Removal of the CCD Unit ------------------------------ 38
8.7. Removal of the Focus Motor -------------------------- 39
8.8. The Application of Grease Method ------------------ 39
which are important for safety. These parts are marked by
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.
heated or damaged by the short circuit.
properly installed.
shock hazards.
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 M
reading must be infinity.
(See Figure 1.)
and a good earth ground, as shown in Figure 1.
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
2. Be careful of the high voltage circuit on E.Capacitor P.C.B. when servicing.
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k
4. After discharging confirm that the capacitor voltage is lower than 10V using a voltmeter.