DMC-LS60PC, DMC-LS60PL, DMC-LS60EB, DMC-LS60EE, DMC-LS60EF, DMC-LS60EG, DMC-LS60EGM, DMC-LS60GC, DMC-LS60GK, DMC-LS60GN - Panasonic Digital Camera Service Manual (repair manual)

dmc-ls60pc, dmc-ls60pl, dmc-ls60eb, dmc-ls60ee, dmc-ls60ef, dmc-ls60eg, dmc-ls60egm, dmc-ls60gc, dmc-ls60gk, dmc-ls60gn service manual
Model
DMC-LS60PC DMC-LS60PL DMC-LS60EB DMC-LS60EE DMC-LS60EF DMC-LS60EG DMC-LS60EGM DMC-LS60GC DMC-LS60GK DMC-LS60GN
Pages
51
Size
2.83 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / DIGITAL CAMERA
File
dmc-ls60pc-dmc-ls60pl-dmc-ls60eb-dmc-ls60ee-dmc-ls.pdf
Date

Read Panasonic DMC-LS60PC / DMC-LS60PL / DMC-LS60EB / DMC-LS60EE / DMC-LS60EF / DMC-LS60EG / DMC-LS60EGM / DMC-LS60GC / DMC-LS60GK / DMC-LS60GN Service Manual online

ORDER NO. DSC0702011CE
B26
Digital Camera
DMC-LS60PC
DMC-LS60PL
DMC-LS60EB
DMC-LS60EE
DMC-LS60EF
DMC-LS60EG
DMC-LS60EGM
DMC-LS60GC
DMC-LS60GK
DMC-LS60GN
DMC-LS70P
DMC-LS70PC
DMC-LS70PL
DMC-LS70EB
DMC-LS70EE
DMC-LS70EG
DMC-LS70EGM
DMC-LS70GC
DMC-LS70GK
DMC-LS70GN
DMC-LS75P
DMC-LS75PC
DMC-LS75PL
2
DMC-LS75EB
DMC-LS75EE
DMC-LS75EF
DMC-LS75EG
DMC-LS75EGM
DMC-LS75GC
DMC-LS75GK
DMC-LS75GN
Vol. 1
Colour
(S)...................Silver Type (except DMC-LS75PC)
(K)...................Black Type (only DMC-LS75P/PC/EB/EE/
EF/EG/EGM)
TABLE OF CONTENTS
PAGE
PAGE
1 Safety Precaution -------------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.) --------3
1.4. How to Discharge the Capacitor on Flash Top
PCB------------------------------------------------------------4
2 Warning --------------------------------------------------------------5
2.1. Prevention of Electro Static Discharge (ESD)
to ElectrostaticallySensitive (ES) Devices -----------5
2.2. How to Replace the Lithium Battery -------------------6
3 Service Navigation------------------------------------------------7
3.1. Introduction --------------------------------------------------7
3.2. General Description About Lead Free Solder
(PbF) ----------------------------------------------------------7
3.3. Important Notice 1:(Other than U.S.A. and
Canadian Market) ------------------------------------------7
3.4. How to Define the Model Suffix (NTSC or PAL
model)---------------------------------------------------------8
4 Specifications ---------------------------------------------------- 11
5 Location of Controls and Components------------------ 12
6 Service Mode ----------------------------------------------------- 14
6.1. Error Code Memory Function ------------------------- 14
6.2. Confirmation of Firmware Version ------------------- 17
7 Service Fixture & Tools --------------------------------------- 18
7.1. Service Fixture and Tools ------------------------------ 18
7.2. When Replacing the Main PCB ---------------------- 19
7.3. Service Position ------------------------------------------ 19
8 Disassembly and Assembly Instructions --------------- 20
8.1. Disassembly Flow Chart-------------------------------- 20
8.2. PCB Location---------------------------------------------- 20
8.3. Disassembly Procedure -------------------------------- 21
8.4. Disassembly Procedure for the Lens --------------- 25
8.5. Assembly Procedure for the Lens ------------------- 27
8.6. Removal of the CCD Unit ------------------------------ 30
8.7. Removal of the Focus Motor -------------------------- 31
8.8. The Applyment of Grease Method ------------------- 31
9 Measurements and Adjustments -------------------------- 32
9.1. Matrix Chart for Replaced Part and Necessary
Adjustment ------------------------------------------------- 32
10 Maintenace -------------------------------------------------------- 33
10.1. Cleaning Lens and LCD Panel ----------------------- 33
3
1 Safety Precaution
1.1.
General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essen-
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
2. An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been over-
heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2.
Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 M
Ω and 5.2 MΩ. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
1.3.
Leakage Current Hot Check
(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5 k
Ω, 10 W resistor, in parallel with a 0.15 μF
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 k
Ω/V or more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the volt-
age at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equiva-
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Figure. 1
4
1.4.
How to Discharge the Capacitor on Flash Top PCB
CAUTION:
1. Be sure to discharge the capacitor on FLASH TOP PCB.
2. Be careful of the high voltage circuit on FLASH TOP PCB when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and Remove the necessary parts/unit.
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k
Ω /5W).
(an equivalent type of resistor may be used.)
3. Put the resistor between both terminals of capacitor on FLASH TOP PCB for approx. 5 seconds.
4. After discharging confirm that the capacitor voltage is lower than 10V using a voltmeter.
Fig. F1
Page of 51
Display

Download Panasonic DMC-LS60PC / DMC-LS60PL / DMC-LS60EB / DMC-LS60EE / DMC-LS60EF / DMC-LS60EG / DMC-LS60EGM / DMC-LS60GC / DMC-LS60GK / DMC-LS60GN Service Manual (Repair Manual)

Here you can read online and download Panasonic DMC-LS60PC / DMC-LS60PL / DMC-LS60EB / DMC-LS60EE / DMC-LS60EF / DMC-LS60EG / DMC-LS60EGM / DMC-LS60GC / DMC-LS60GK / DMC-LS60GN Service Manual in PDF. DMC-LS60PC / DMC-LS60PL / DMC-LS60EB / DMC-LS60EE / DMC-LS60EF / DMC-LS60EG / DMC-LS60EGM / DMC-LS60GC / DMC-LS60GK / DMC-LS60GN service manual will guide through the process and help you recover, restore, fix, disassemble and repair Panasonic DMC-LS60PC / DMC-LS60PL / DMC-LS60EB / DMC-LS60EE / DMC-LS60EF / DMC-LS60EG / DMC-LS60EGM / DMC-LS60GC / DMC-LS60GK / DMC-LS60GN Digital Camera. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.