DMC-FT1EB, DMC-FT1EE, DMC-FT1EF, DMC-FT1EG, DMC-FT1EP, DMC-FT1GC, DMC-FT1GJ, DMC-FT1GN, DMC-FT1SG, DMC-TS1P, DMC-TS1PC, DMC-TS1PU, DMC-TS1GH, DMC-TS1GK, DMC-TS1GT - Panasonic Digital Camera Service Manual (repair manual)

dmc-ft1eb, dmc-ft1ee, dmc-ft1ef, dmc-ft1eg, dmc-ft1ep, dmc-ft1gc, dmc-ft1gj, dmc-ft1gn, dmc-ft1sg, dmc-ts1p, dmc-ts1pc, dmc-ts1pu, dmc-ts1gh, dmc-ts1gk, dmc-ts1gt service manual
Model
DMC-FT1EB DMC-FT1EE DMC-FT1EF DMC-FT1EG DMC-FT1EP DMC-FT1GC DMC-FT1GJ DMC-FT1GN DMC-FT1SG DMC-TS1P DMC-TS1PC DMC-TS1PU DMC-TS1GH DMC-TS1GK DMC-TS1GT
Pages
65
Size
5.37 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / DIGITAL CAMERA
File
dmc-ft1eb-dmc-ft1ee-dmc-ft1ef-dmc-ft1eg-dmc-ft1ep-.pdf
Date

Read Panasonic DMC-FT1EB / DMC-FT1EE / DMC-FT1EF / DMC-FT1EG / DMC-FT1EP / DMC-FT1GC / DMC-FT1GJ / DMC-FT1GN / DMC-FT1SG / DMC-TS1P / DMC-TS1PC / DMC-TS1PU / DMC-TS1GH / DMC-TS1GK / DMC-TS1GT Service Manual online

ORDER NO.DSC0903016CE
B26
Digital Camera
Model No.
DMC-FT1EB
       DMC-FT1EE
       DMC-FT1EF
       DMC-FT1EG
       DMC-FT1EP
       DMC-FT1GC
       DMC-FT1GJ
       DMC-FT1GN
       DMC-FT1SG
       DMC-TS1P
       DMC-TS1PC
       DMC-TS1PU
       DMC-TS1GH
       DMC-TS1GK
       DMC-TS1GT
VOL.1
Colours
(A)....................Blue Type (only DMC-FT1EB/EF/EG/EP/
GC/GN, DMC-TS1PC/PU)
(D)....................Orange Type (Except DMC-FT1EB)
(G)....................Green Type (Except DMC-FT1EB)
(S)....................Silver Type (Except DMC-FT1EF, DMC-
TS1GT)
2
TABLE OF CONTENTS
PAGE
PAGE
1 Safety Precautions -----------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1)---------3
1.4. How to Discharge the Capacitor on Flash
PCB------------------------------------------------------------4
2 Warning --------------------------------------------------------------5
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatic Sensitive (ES) Devices ---------------5
2.2. How to Recycle the Lithium Ion Battery (U.S.
Only)-----------------------------------------------------------5
2.3. Caution for AC Cord (For EB/GC/GH) ----------------6
2.4. How to Replace the Lithium Battery -------------------7
3 Service Navigation------------------------------------------------9
3.1. Introduction --------------------------------------------------9
3.2. Air-leak test (inspection)----------------------------------9
3.3. Replacing the waterproof packing (waterproof
seal) -----------------------------------------------------------9
3.4. Lens Unit -----------------------------------------------------9
3.5. General Description About Lead Free Solder
(PbF) ----------------------------------------------------------9
3.6. Important Notice 1:(Other than U.S.A. and
Canadian Market)  --------------------------------------- 10
3.7. How to Define the Model Suffix----------------------- 11
4 Specifications ---------------------------------------------------- 15
5 Location of Controls and Components------------------ 21
6 Service Mode ----------------------------------------------------- 23
6.1. Error Code Memory Function ------------------------- 23
6.2. ICS (Indication of additional Camera Settings
when picture was taken) function -------------------- 26
7 Troubleshooting Guide---------------------------------------- 28
7.1. Service and Check Procedures ---------------------- 28
7.2. Air-leak Test ----------------------------------------------- 31
7.3. Air-leak Test (Inspection) ------------------------------- 32
8 Service Fixture & Tools --------------------------------------- 34
8.1. Service Fixture and Tools ------------------------------ 34
8.2. When Replacing the Main PCB ---------------------- 35
8.3. Service Position ------------------------------------------ 35
9 Disassembly and Assembly Instructions --------------- 37
9.1. Disassembly Flow Chart-------------------------------- 37
9.2. PCB Location---------------------------------------------- 37
9.3. Disassembly Procedures------------------------------- 38
10 Measurements and Adjustments -------------------------- 48
10.1. Matrix Chart for Replaced Part and Necessary
Adjustment ------------------------------------------------- 48
11 Maintenance ------------------------------------------------------ 49
11.1. Cleaning Lens and LCD Panel ----------------------- 49
3
1 Safety Precautions
1.1.
General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These parts are marked by
 in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essen-
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION, shock
fire, or other hazards. Do not modify the original design
without permission of manufacturer.
2. An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. It a short
circuit is found, replace all parts which have been over-
heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2.
Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1M
Ω and 5.2MΩ. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
1.3.
Leakage Current Hot Check
(See Figure 1)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5k
Ω, 10 W resistor, in parallel with a 0.15μF
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 k
Ω/V or more sensitivity, to
measure the potential across the resistor. 
4. Check each exposed metallic part, and measure the volt-
age at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equiva-
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Figure 1
4
1.4.
How to Discharge the Capacitor on Flash PCB
• This unit equipped with two pieces of capacitors as flash charging capacitors.
“Either one of the capacitor discharging operation” makes discharging for others as well.
CAUTION:
1. Be sure to discharge the capacitor on FLASH PCB.
2. Be careful of the high voltage circuit on FLASH PCB when servicing. 
[Discharging Procedure] 
1. Refer to the disassemble procedure and remove the necessary parts/unit.
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k
Ω /5W). 
(An equivalent type of resistor may be used.) 
3. Put the resistor between both terminals of capacitor on FLASH PCB for approx. 5 seconds. 
4. After discharging confirm that the capacitor voltage is lower than 10V using a voltmeter. 
Fig. F1
Page of 65
Display

Download Panasonic DMC-FT1EB / DMC-FT1EE / DMC-FT1EF / DMC-FT1EG / DMC-FT1EP / DMC-FT1GC / DMC-FT1GJ / DMC-FT1GN / DMC-FT1SG / DMC-TS1P / DMC-TS1PC / DMC-TS1PU / DMC-TS1GH / DMC-TS1GK / DMC-TS1GT Service Manual (Repair Manual)

Here you can read online and download Panasonic DMC-FT1EB / DMC-FT1EE / DMC-FT1EF / DMC-FT1EG / DMC-FT1EP / DMC-FT1GC / DMC-FT1GJ / DMC-FT1GN / DMC-FT1SG / DMC-TS1P / DMC-TS1PC / DMC-TS1PU / DMC-TS1GH / DMC-TS1GK / DMC-TS1GT Service Manual in PDF. DMC-FT1EB / DMC-FT1EE / DMC-FT1EF / DMC-FT1EG / DMC-FT1EP / DMC-FT1GC / DMC-FT1GJ / DMC-FT1GN / DMC-FT1SG / DMC-TS1P / DMC-TS1PC / DMC-TS1PU / DMC-TS1GH / DMC-TS1GK / DMC-TS1GT service manual will guide through the process and help you recover, restore, fix, disassemble and repair Panasonic DMC-FT1EB / DMC-FT1EE / DMC-FT1EF / DMC-FT1EG / DMC-FT1EP / DMC-FT1GC / DMC-FT1GJ / DMC-FT1GN / DMC-FT1SG / DMC-TS1P / DMC-TS1PC / DMC-TS1PU / DMC-TS1GH / DMC-TS1GK / DMC-TS1GT Digital Camera. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.