Read Panasonic WV-CW970 / WV-CW974 Service Manual online
2-8
3.3. Dip Switch Setting
8 Peel the RS485 Setting Label which covers switch holes
on top of the camera.
8 Set the DIP switches (SW1, 2) on the Switch Board as
shown in Fig. 3-3-1.
8 Stick the labels as it was.
3.4. Setting Up for Standard Picture
8 The adjustment should be done after 30 minutes warm-
up.
8 Set the Logarithmic Gray Scale Chart.
8 Incident light of 1 400 lx ± 50 lx on the Logarithmic Gray
8 Incident light of 1 400 lx ± 50 lx on the Logarithmic Gray
Scale Chart.
8 Aim the Camera at the Logarithmic Gray Scale Chart.
8 Set the Camera by the Remote E.V.R. Adjustment Kit so
8 Set the Camera by the Remote E.V.R. Adjustment Kit so
that the Logarithmic Gray Scale Chart becoms full pic-
ture on the Underscanned Colour Video Monitor.
ture on the Underscanned Colour Video Monitor.
8 Adjust the Lens Focus by the Remote E.V.R. Adjustment
Kit to obtain correct focal point.
8 The adjustments should be done with this Standard
Picture, unless otherwise specified.
(4) Installing E.V.R Adjustment Program
8 Make a copy of following necessory files to your comput-
er from original floppy disk.
RADJ2.EXE
CW97E.SEQ
CW97AF1.SEQ
CW97TLT.SEQ
CW97PRE.SEQ
CW97E.EV2
8 The Example given here is for A 2 drive computer, your
procedure might vary slightly depending on the drive
configuration.
configuration.
8 Confirm that the contents of CONFIG.SYS file on your
computer is DEVICE=ANSI.SYS (Basic).
8 Insert floppy disk containing the E.V.R. Adjustment
Program into your floppy drive (for example,drive:A) and
type A:
type A:
8 At the prompt, type CD IBMPC and press ENTER key.
8 Type COPY RADJ2.EXE B: and press ENTER key.
8 Type CD\ and press ENTER key.
8 Type CD SEQ and press ENTER key.
8 Type COPY CW97E.SEQ B: and press ENTER key.
8 Type COPY CW97AF1.SEQ B: and press ENTER key.
8 Type COPY CW97TLT.SEQ B: and press ENTER key.
8 Type COPY CW97PRE.SEQ B: and press ENTER key.
8 Type CD\ and press ENTER key.
8 Type CD EVR and press ENTER key.
8 Type COPY CW97E.EV2 B: and press ENTER key.
8 After completing installation of program, you are ready to
8 Type COPY RADJ2.EXE B: and press ENTER key.
8 Type CD\ and press ENTER key.
8 Type CD SEQ and press ENTER key.
8 Type COPY CW97E.SEQ B: and press ENTER key.
8 Type COPY CW97AF1.SEQ B: and press ENTER key.
8 Type COPY CW97TLT.SEQ B: and press ENTER key.
8 Type COPY CW97PRE.SEQ B: and press ENTER key.
8 Type CD\ and press ENTER key.
8 Type CD EVR and press ENTER key.
8 Type COPY CW97E.EV2 B: and press ENTER key.
8 After completing installation of program, you are ready to
use the E.V.R. Adjustment Program.
RS48
5Se
tting
S TART
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
SW
1
SW2
Camera top view
RS485 Setting Label
DIP Switches
SW2
4-bit DIP SW
#1 : ON, #2-#4 : OFF
4-bit DIP SW
#1 : ON, #2-#4 : OFF
SW1
8-bit DIP SW
#1-#8 : OFF
8-bit DIP SW
#1-#8 : OFF
Fig. 3-3-1
Click on the first or last page to see other WV-CW970 / WV-CW974 service manuals if exist.